Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
. psi (3.5 kPa)) before appliance is connected. Be sure to release air pressure from the gas line before connection is made to the appliance. Excessive pressure will damage the gas control and may cause a gas leak. • Gas Leak Test: Make sure the gas connections are tight. Turn on the gas and coat each joint with a non-corrosive gas leak check solution. Air bubbles will form indicating any leaks. DO NOT USE A FLAME OR ANY TYPE OF IGNITION SOURCE TO CHECK FOR LEAKS. All leaks must be corrected before proceeding with installation. • The appliance must only be installed in a solid-fuel burning fireplace with the flue damper clamped open according to Tables 1 and 2. The fireplace must be constructed of non-combustible material. • The minimum permanent free opening (in square inches) that must be provided by the fireplace chimney or damper to vent the flue gases is provided in Tables 1 and 2. If the free opening is smaller than the specified area, do not use this appliance. • The damper must be removed or fixed in a manner in which will secure it open. Some jurisdictions require the damper to be removed or permanently welded fully open. Check with state and local codes. • Be sure that the chimney is completely unobstructed to ensure proper ventilation of flue gases including carbon monoxide (CO). CO (a poisonous gas) is tasteless, odorless, colorless and undetectable without proper equipment. • Refer to Table 3 to determine minimum fireplace opening requirements before proceeding. WARNING Fire Risk Explosion Risk High pressure will damage valve. • Disconnect gas supply piping BEFORE pressure testing gas line at test pressures above 1/2 psig. • Close the manual shutoff valve BEFORE pressure testing gas line at test pressures equal to or less than 1/2 psig. G. Negative Pressure Negative pressure results from the imbalance of air available for the fireplace to operate properly. Causes for this imbalance include: • Exhaust fans (kitchen, bath, etc.). • Range hoods. • Combustion air requirements for furnaces, water heaters and other combustion appliances. • Clothes dryers. • Location of return-air vents to furnace or air conditioning. • Imbalances of the HVAC air handling system. • Upper level air leaks: recessed lighting, attic hatch opening, duct leaks. WARNING Asphyxiation Risk This appliance produces carbon monoxide (CO). • The free opening areas (in square inches) of the chimney damper as shown in the following tables must be met. • User must make sure damper is locked open. • The installer is responsible to ensure proper ventilation of flue gases before appliance is used. Fire needs to draft properly for safe operation. Table 1 for Factory Built Fireplaces Free Opening Area (in square inches) of Chimney Damper for Venting combustion Products from Decorative Appliances for Installation in Solid Fuel Burning Fireplaces. Chimney Ht. (Feet)* GO318 GO 24 & 324 GO 30 & 330 10 not approved not approved not approved 15 38.5 38.5 45.4 20 31.2 31.2 37.4 25 27.3 27.3 31.2 30 24.6 24.6 28.3 35 22.1 22.1 25.5 40 20.4 20.4 23.8 Table 2 for Masonary Built Fireplaces Free Opening Area (in square inches) of Chimney Damper for Venting combustion Products from Decorative Appliances for Installation in Solid Fuel Burning Fireplaces. Chimney Ht. (Feet)* GO318 GO 24 & 324 GO 30 & 330 6 64 64 71.4 8 59.7 59.7 66.9 10 54.3 54.3 60.2 15 48.8 48.8 54.1 20 44.4 44.4 49.1 30 40.3 40.3 44.5 * Height is measured from the hearth to the top of the chimney. Minimum height is 6 ft. Table 3 for Minimum Fireplace Dimensions Log Set Front Opening Depth Height Rear Width Natural BTU GO24 32 in. 20 in. 18 in. 21 in. 73,000 GO30 38 in. 20 in. 18 in. 27 in. 80,000 GO318 32 in. 23 in. 22 in. 21 in. 77,000 GO324 34 in. 23 in. 22 in. 22 in. 86,000 GO330 40 in. 23 in 22 in. 29 in. 86,000 H. Inspect the Appliance and Components • Remove the contents from the carton labeled “Burner”. Attached to the burner are tags identifying the manufacturer name, serial number, model number (including gas log size), BTU ratings, gas type, etc. • Review the attached tags before proceeding. Ensure that all minimum fireplace dimension requirements are achieved using Table 3. See Figure 1. Ensure the gas type provided in the fireplace coincide with the gas type marked on the tag. • The burner is assembled with the controls installed at the factory and is designed to connect one end of the 3/8 in. supply line before placing inside the fireplace. Ensure the connection is tightened using a 3/4 in. wrench. • Place the burner towards the rear and center of the fireplace and connect to the gas line. Follow instructions in “F. Gas Pressure” to check for gas leaks. Figure 4 Placing Vermiculite .Pour vermiculite over the sand in the pans until they are full. See Figure 4. Note: For best results, do not pack down the rock wool. The placement of rock wool can have an effect on flame pattern and may need to be adjusted to achieve a desired appearance. Figure 1 Measure Firebox Figure 5 Pl...
Эта инструкция также подходит к моделям:Камины - GO318MTCH (5.18 mb)
Камины - GO330MTCH (5.18 mb)
Камины - GO24MTCH (5.18 mb)
Камины - GO30MTCH (5.18 mb)