Оценок - 4, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
This will ensure that clearance to combustibles is maintained within the cavity. It is best to frame your fireplace after it is positioned and the vent system is installed. Use 2x4's and frame to local building codes. FIGURE 15. See PAGE 7 for bar type / countertop installation. FIGURE 15 A = 221/8" minus finishing material thickness, each side. BRICK PANEL INSTALLATION Install the base panels as illustrated in steps 1-4 on page 9. Both side panels sit under the bracket tab. Holding the side panel in position, bend down the tab to secure. DE FIGURES 16a-cTAIL 6. RETAINER RETAINER STEP 5 STEP 6 DETAIL 5 & 6 Combustible materials may be installed flush with the front of the fireplace but must not cover any of the black face- areas of the fireplace. Non-combustible material (brick, stone or ceramic tile) may protrude in these areas. It is not necessary to install a hearth extension with this fireplace system. When roughing in the fireplace, raise the fireplace to accommodate for the thickness of the finished floor materials, i.e. tile, carpeting, hard wood, which if not planned for will interfere with the opening of the lower access door and the installation of many decorative flashing accesso ries. Objects placed in front of the fireplace should be kept a minimum of 48" away from the glass front faces. FINISHING Refer to pages 14-17 for complete instructions regarding mantle requirements and installations, log placement, glass door and upper and lower louvre attachments. DRYWALL DRYWALL 4" MIN FIGURE 17 W415-0320 / D / 01.06.07 ISLAND INSTALLATION PROCEDURE BRICK PANEL INSTALLATION FRAMING ISLAND INSTALLATION PROCEDURE BRICK PANEL INSTALLATION FRAMING It is best to frame your fireplace after it is positioned. Use 2x4's and frame to local building codes. FIGURE 18. A = 221/8 " minus finishing material thickness each side. B = 36 " minus finishing material thickness each end. FIGURE 18 To install the fireplace face flush with the finished wall, position the framework to accommodate the thickness of the finished wall. FIGURE 19 Install the base panels as illustrated in steps 1-4 on page 9. FACING Combustible materials may be installed flush with the front of the fireplace but must not cover any of the black face- areas of the fireplace. Non-combustible material (brick, stone or ceramic tile) may protrude in these areas. It is not necessary to install a hearth extension with this fireplace system. When roughing in the fireplace, raise the fireplace to accommodate for the thickness of the finished floor materials, i.e. tile, carpeting, hard wood, which if not planned for will interfere with the opening of the lower access door and the installation of many decorative flashing accessories. Objects placed in front of the fireplace should be kept a minimum of 48" away from the glass front FIGURE 20 DRYWALL DRYWALL faces. FINISHING Refer to pages 14-17 for complete instructions regarding mantle requirements and installations, log placement, glass door and upper and lower louvre attachments. W415-0320 / D / 01.06.07 13 W415-0320 / D / 01.06.07 Proceed once the vent installation is complete. 1. Move the fireplace into position and secure using the nailing tabs and/or secure to the floor through the 1/4"o holes located at either end of the base. 2. Route a 3/8" N.P.T. black iron gas line, 1/2" type-L copper tubing or equivalent to the fireplace. 3. For ease of accessibility, an optional remote wall switch or millivolt thermostat may be installed in a convenient location. Route 2-strand (solid core) millivolt wire through the electrical hole located at the bottom left side of the unit. The recommended maximum lead length depends on wire size: WIRE SIZE MAX. LENGTH 14gauge 100 feet 16gauge 60 feet 18gauge 40 feet Attach the one lead to terminal 3 (located on the gas valve) and the other lead to the vent safety switch wire ( located loose in the valve compartment). See FIGURE 3. Do not connect either the wall switch, thermostat or gas valve to electricity (110 volts). 4. Install rigid black pipe, 1/2" type-L copper tubing or, if local codes permit, a 3/8" flex connector and shutoff valve to the gas line and the fireplace gas valve. Seal and tighten securely. An adapter fitting is required between the gas valve and the copper tubing or flex connector. DO NOT KINK FLEXIBLE CONNECTOR. FIGURE 6. 5. Check for gas leaks by brushing on a soap and water solution. Do not use open flame. 6. Mark the appropriate boxes on the rating plate label to indicate the model type. Purge all gas lines with the glass door of the fireplace open. Assure that a continuous gas flow is at the burner before closing the door. FIGURE 22 PI PILOT 3 1 2 NO LOT HI LO FF O FIGURE 21 FIGURE 23 GAS INSTALLATION Combustible mantle clearance can vary according to the mantle depth. Use the graph to help evaluate the clearance needed. The three-sided top extension piece may be removed if non-combustible framing is faced with a non-combustible material. FIGURE 24 Da...
Эта инструкция также подходит к моделям:Камины - BGNV40-N (1.08 mb)