Оценок - 2, средний балл: 3
(
)
)
|
Фрагмент инструкции
Use the graph to help evaluate the clearance needed. Figures 11 a & b. FIGURE 13a FIGURE 13b A CORNER POST NAILING TAB TOP SLOT FINISHING MATERIAL C CENTRE HOLE B W415-0377 / C / 09.23.05 LOUVRE BRACKET INSTALLATION FINISHING L42 LOUVRE INSTALLATION LOUVRE BRACKET INSTALLATION FINISHING L42 LOUVRE INSTALLATION 1. Align the holes in the louvre brackets with the pre- drilled holes in the firebox, as shown. 2. Secure louvre brackets in place using screws. FIGURE 14 FIGURE 17 DOOR INSTALLATION The upper louvres must be removed to allow the door to be removed. Release the two door latches, located across the top of the door and lift off the lower door bracket. GDL42 LOUVRE INSTALLATION HINGE SCREEN 16 15 DOOR LATCH UPPERLOUVRE Insert the upper louvres into the slots on both brackets. Attach each hinge on the lower louvre assembly to the lip of the fireplace base with 2 screws. Position the hinge screen into place and with the control door open, secure to the fireplace using three screws. SLOT TAB A B HINGE CLIP SLOT Remove the backing of the logo supplied and place on the glass viewing door, as indicated. UPPER LOUVRES Insert the louvre tabs into the slots located at the top left and right corners of the unit. LOWER LOUVRES Insert the hinge clips into the slots located at the bottom left and right corners of the unit. To remove the louvres, pull the back tabs of the clips forward, while pushing the louvre assembly back. Lift the clip. LOGO PLACEMENT FIGURE 18 LOGO ." ." W415-0377 / C / 09.23.05 LOG PLACEMENT PHAZERTM logs and glowing embers, exclusive to Napoleon Fireplaces, provide a unique and realistic glowing effect that is different in every installation. Take the time to carefully position the glowing embers for a maximum glowing effect. Log colours may vary. During the initial use of the fireplace, the colours will become more uniform as colour pigments burn in during the heat activated curing process. #1 FIGURES 19a-e 1. Place the back log (#1) onto the log support tray and in front of the tabs. The tabs maintain an air space between the log and firebox back to facilitate combustion air flow. Ensure that the back of the log rests against the brackets on the back wall of the firebox. #3#2 4. Place the bottom of the left crossover log (#4) against #4 #5 the left outermost grate post and the top into the pocket provided on the back log. Position the notch located on the end of the center log (#5) against the middle grate post with the other end of the log resting in the pocket of the left crossover log. #6 5. Place the bottom of the right crossover log (#6) against the right outermost grate post and the top into the pocket provided on the center log (#5). CHARCOAL EMBERS Randomly place the charcoal embers along the front and sides of the log support tray in a realistic manner. Fine dust found in the bottom of the bag should not be used. VERMICULITE 2. Move the two small logs (#2 & #3) into position, lining up the studs located on the Sprinkle vermiculite around the charcoal embers. Note: Both charcoal embers and vermiculite are not to be placed on the burner. Place the lumps between the logs in a realistic manner taking care not to block any of the burner ports. GLOWING EMBERS CHARCOAL LUMPS burner with the holes on the bottom of the logs. 3. Tear the glowing embers into pieces and place along the front row of ports covering all of the burner area in front of the small logs (#2 & #3). Care should be taken to shred the embers into thin, small irregular pieces as only the exposed edges of the fibre hairs will glow. The ember material will only glow when exposed to direct flame; however, care should be taken to not block the burner ports. Blocked burner ports can cause an incorrect flame pattern, carbon deposits W415-0377 / C / 09.23.05 10 W415-0377 / C / 09.23.05 Attach the connectors from the black and white wires to the thermodisc and secure the thermodisc bracket to the securing stud at the bottom left of the unit using a lock washer and wing nut. Ensure that the thermodisc touches the firebox wall. Attach the connectors from the black and red wires to the blower. Attach and secure the variable speed switch using the nut provided. Plug the harness cord into the receptacle. The wire harness provided in this kit is a universal harness. When installed, ensure that any excess wire is contained, preventing it from making contact with moving or hot objects. Because the blower is thermally activated, when turned on, it will automatically start approximately 15 minutes after lighting the fireplace and will run for approximately 30-45 minutes after the fireplace has been turned off. Use of the fan increases the output of heat. Drywall dust will penetrate into the blower bearings causing irreparable damage. Care must be taken to prevent drywall dust from coming into contact with the blower or its compartment. Any damage resulting from this condition is not covered by the warranty policy. INSTALLATION TO BE DONE BY A...
Эта инструкция также подходит к моделям:Камины - BGNV42P (1.56 mb)