Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
WARNING Do not operate appliance with the glass frontremoved,cracked or broken. AVERTISSEMENT Ne pas utiliser l'appareil si le panneau frontal en verre n'est pas en place, est craque ou brise. WARNING Any safety screen or guard removed for servicing the appliance must be replaced prior to operating the appliance. AVERTISSEMENT Tout ecran ou protecteur retire pour permettre l’entretien de l’appareil doit etre remis en place avant de mettre l’appareil en marche. Only doors certified with the appliance shall be used. Seules des portes certifiees pour cet appareil doivent etre utilisees. CAUTION: DO NOT abuse glass door by striking or slamming shut. These are direct-vent appliances. They are designed to operate only when the front glass enclosure panels are installed. Generally the front glass enclosure panel should not be removed except to gain access to the components within the firebox. Removing Glass Enclosure Panels (see Figure 4) 1. Remove the top louver assembly the control compartmentlouverassemblybyliftingthem up,thenpullingout(see removalinstructions on Page 8). 2. Remove the control compartment access door (see removal instructions on Page 8). 3. Locate the two (2) latches at the top of the control compartment. To disengage the two latches from the bottom vee-flange of the glass enclosure panel, reach for the handles located towards the back of the latches and pull the handles down toward the front of the appliance. 4. Swing the bottom of the door out and raise it slightly to lift the top flange of the door frame away from the appliance. Installing Glass Enclosure Panels (see Figure 4) 1. Visuallyinspectthegasketonthebacksideof thepanels.Thegasketsurfacemustbeclean, free of irregularities and seated firmly. 2. Position the glass enclosure panel in front of the firebox opening at a 45 degree angle and engage the top flange over the lip at the top of the firebox opening. 3. Swing the glass enclosure panel down and back. Ensure the gasket seats evenly as the panel draws shut. Engage the Vee-flange at the bottom of the panel with the latches and close the latches to secure the panel. 4. Reinstall the control compartment door (see installation instructions on Page 8, Reinstalling Control Compartment Door). Top Flange on Glass Door Bottom Vee-flange Glass Door Glass Door Latch Glass Door Firebox Floor Figure 4 Note: When installing the glass door, ensure the spacing on both sides are equal. INSTALLING OR REMOVING GLASS DOOR INSTALLING LOG SET, VOLCANIC STONE AND GLOWING EMBERS WARNINGS • • • DO NOT attempt to install the logs until the appliance instal lationhasbeencompleted,the gas line connected and tested for leaks and the initial burner operation has been checked out. Thesizeandpositionofthelog set was engineered to give the appliance a safe, reliable and attractive flame pattern. Any attempt to use a different log set in the fireplace will void the warranty and will result in incomplete combustion, soot ing, and poor flame quality. Logs get very hot and will remain hot up to one hour after gas supply is turned off. Handle only when logs are cool. Turn off all electricity to the appliance before you install grate, volcanic stone, embers and logs. NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. 12 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. FRONT OF FIREPLACE REAR BURNER FRONT BURNER...
Эта инструкция также подходит к моделям:Камины - SDV SDVPF-N-B (2.24 mb)
Камины - SDV SDVPF-N-B (2.24 mb)
Камины - SDV SDVPF-N-B (2.24 mb)
Камины - SDV SDVST-N-B (2.24 mb)