Оценок - 2, средний балл: 3
(
)
)
|
Фрагмент инструкции
Configuring Communications Settings To change the communications settings, from the Home screen, select Configure > Communications. serial Port 1—select the input/output format to use when connecting your unit to external NMEA devices, a personal computer, or other Garmin devices. • Garmin Data Transfer—the proprietary format used to upload, download, or exchange data with a computer or another Garmin unit. • Garmin Remote sonar—allows you to connect a GarminGSD 21orGSD 22serially. • NMEA In/NMEA Out—supports the input or output ofstandardNMEA0183data,DSC, and sonarNMEAinputsupport forthe DPT,MTW, and VHW sentences. • NMEA high speed—supports the input or output of standard 0183 data for most AIS receivers. • None—provides no interfacing capabilities. NMEA setup—enable or disable NMEA output sentences for sounder, route, system, and Garmin NMEA settings. To enable or disable NMEA output sentences: 1. From the Home screen, select Configure > Communications > NMEA Setup. 2. Select a setting (Sounder, Route, System, or Garmin). 3. Select a NMEA output sentence. GPSMAP® 2008/2108 Owner’s Manual ConfigUring The UniT 4. Select Off to disable, or select On to enable the NMEA output sentence. Posn. Precision—adjust the number of digits (Two Digits, Three Digits, or Four Digits) to the right of the decimal point for transmission of NMEA output. Waypoint—select how the unit outputs waypoint identifiers(Names or Numbers). Setting Alarms You can set the unit to sound an audible alarm when certain conditions are met. By default, all alarms are turned off. To set an alarm: 1. From the Home screen, select Configure > Alarms. GPSMAP® 2008/2108 Owner’s Manual 2. Select an alarm category (Navigation, System, or Sonar Warnings). 3. Select an alarm. 4. Select On to turn the alarm on, and then use the ROCKER to specify alarm information. Press up or down on the ROCKER to increase or decrease. Press left or right on the ROCKER to move fields. Setting Navigation Alarms To set a navigation alarm, from the Home screen, select Configure > Alarms > Navigation. Anchor Drag—set an alarm to sound when you exceed a specifieddriftdistance. Arrival—set an alarm to sound when you are within aspecified distanceor time from a destination waypoint. ConfigUring The UniT Off Course—set an alarm to sound when you are off course byaspecified distance. Setting System Alarms To set a system alarm, from the Home screen, select Configure > Alarms > system. Clock—set an alarm using the system clock. The unit must be on for the clock alarm to work. battery—set an alarm to sound when the battery reaches a user-determined low voltage. GPs Accuracy—set an alarm to sound when the GPS location accuracy falls outside the user-determined value. Setting Sonar Alarms To set a sonar alarm, from the Home screen, select Configure > Alarms > sonar. shallow Water/Deep Water—set an alarm to sound when the depth is less than or greater than the specified value. Water Temp—set an alarm to sound when the transducer reports a temperature that is 2° F (1.1° C) above or below the specifiedtemperature. Fish—set an alarm to sound when the unit detects a suspendedtarget of the specifiedsymbols. NOTE: You must have a transducer connected. If your unit does not have a built-in sounder, then you mustinstalla GSD 21or GSD 22 sounder module to receive sonar information. Configuring My Boat To configuresettings foryour boat, from theHome screen, select Configure > My boat. Auto Guidance—set the Auto Guidance parameters for your boat: • safe Depth—set the minimum depth (referred to the chart depth datum) to allow when calculating an auto guidance path. • safe height—set the minimum height (referred to the chart height datum) of a bridge that your boat can safely travel under. Keel Offset—offset the surface reading for the depth of a keel. This makes it possible to measure depth from the bottom of your keel instead of from the transducer’s location. Enter a positive number to offset for a keel. You can enter a negative number to GPSMAP® 2008/2108 Owner’s Manual ConfigUring The UniT compensate for a large vessel that may draw several feet of water. To adjust the Keel Offset: 1. From the Home screen, select Configure > My Boat > Keel Offset. 2. Use the ROCKER to set the value of the keel offset. 3. Press to accept the number. NOTE: Press to cancel your changes and return to the My Boat screen. Transducer at Surface Enter a (+) positive number to show depth from the bottom of the keel. Transducer at Bottom of Keel Enter a (-) negative number to show depth from the surface. Keel Offset Transducer—select the transducer type (Dual GPSMAP® 2008/2108 Owner’s Manual Frequency or Dual beam), set the temperature source, sonar cone angles, and calibrate water speed. • Temp source—set the temperature source (Transducer or NMEA). • sonar Cone Angles—when using a transducer other than the standard Garmin transducer, you can set the angle, in degrees, of the sonar cone so it is accurately depicted on...
Эта инструкция также подходит к моделям:Эхолоты - GPSMAP 2108 (25.22 mb)