Оценок - 1, средний балл: 4
(
)
)
|
Фрагмент инструкции
When using Garmin Radar and sonar modules, you will need a network expander GMS10. insTallinG The UniT Install the Wiring Harness The unit comes with a wiring harness that connects the unit to power and the transducer with one easy-toremove connection and provides interface capabilities for connecting external devices. The color code in the diagram (see page 41 for GPSMAP2008/2108) indicates the appropriate harness connections. The replacement fuse is a AGC/ 3AG - 3 Amp fuse. If it is necessary to extend the power wires, use 22AWGwire. DO NOTcut the transducer cable, because this voids your warranty. You can wire the unit directly to the battery. If your boat has an electrical system, you might be able to wire the unit directly to an unused holder on your current fuse block. If you are using the boat’s fuse block, remove the in-line fuse holder supplied with the unit. CAuTION: The maximum unit input voltage is 35VoltsDC.Do not exceed this voltage, because this can damage the unit and void the warranty. GPSMAP® 2008/2108 Owner’s Manual 39 insTalling The UniT NOTE: During a typical installation, use only the Red and Black wires. The other wires do not have to be connected for normal operation of the unit. For information on connecting to a NMEA or CANet compatible device, see page 41. To install the wiring harness: 1. Use a test light or voltmeter to determine the polarity of the voltage source. 2. Connect the Red (+ or positive) wire to the positive voltage terminal. (If you use the boat’s fuse block, route the positive connection through the fuse, as shown on the diagram.) 3. Connect the Black (- or ground) wire to the negative voltage terminal. 4. Install or check the 3-Amp fuse (on the boat’s fuse block or in the in-line holder). 5. Align the notches on the cable plug and on the back of the unit. Insert the cable into the connector, and turn the lock ring counter clockwise until it stops. 3-Amp To 10-35 Volt boat supply 2A3A- +Boat ground fuse To Unit Fuse block — + GPSMAP® 2008/2108 Owner’s Manual insTalling The UniT PIN 7 - Yellow (Alarm) PIN 8 - Black (Ground) PIN 13 - Red (DC Positive) PIN 7 - Yellow (Alarm) PIN 12 - White (CANet H) PIN 16 - Green (CANet L) PIN 18 - Blue (NMEA Out) GPSMAP 2008 Pin Assignment PIN 8 - Black (Ground) PIN 13 - Red (DC Positive) PIN 18 - Blue (NMEA Out) GPSMAP 2108 Pin Assignment (VIOLET)NMEA2IN+ (GREY)NMEA2IN- (VIOLET) NMEA 2 IN+ (GREY) NMEA 2 IN- (VIOLET)NMEA2IN+ (GREY)NMEA2IN- (VIOLET) NMEA 2 IN+ (GREY) NMEA 2 IN- ( ((L LLI IIG GGH HHT TT G GGR RRE EEE EEN NN) )) N NNM MME EEA AA 2 22 O OOu uut+ ++ ( ((L LLI IIG GGH HHT TT G GGR RRE EEE EEN NN) )) N NNM MME EEA AA 2 22 O OOu uut+ ++ R RRRRX XXXXD DDDD+ N N+N+++ NNM MMMME EEEEA AAAA D DDDDe eeeev vvvvi iiiic cccce eeee ( ((P PPI IIN NNK KK) )) N NNM MME EEA AA 2 22 O OOu uut -2 2-222- ( ((P PPI IIN NNK KK) )) N NNM MME EEA AA 2 22 O OOu uut - -- R RRRRX XXXXD DDDD- ---- GPSMAP 2008 Wiring Harness GPSMAP 2108 Wiring Harness R RRRRX XXXXD DDDD+ N N+N+++ NNM MMMME EEEEA AAAA D DDDDe eeeev vvvvi iiiic cccce eeee 2 2222 R RRRRX XXXXD DDDD- ---- GPSMAP® 2008/2108 Owner’s Manual 41 insTalling The UniT Connecting to a NMEA device You can connect the unit to other NMEA compatible equipment, suchas a DSC orAIS device.Refer to the wiring diagram on page 41 for connecting the unit to NMEA compatible devices. To install the wiring harness to a GPS or other NMEA device: 1. Follow the voltage source installation steps (see page 40). For Garmin units, the ground (Black) wires serve as NMEA ground and must be attached together or on the same terminal. Refer to the wiring diagram of your GPS unit for wire identification. 2. Connect the Blue (NMEA Out 1) wire from the unit to the NMEA In wire on the NMEA unit’s wiring harness, and the brown (NMEA In 1) wire to the NMEA Out wire on the NMEA unit’s wiring harness. 3. Repeat step 2 using the Grey and Violet wires for an additional NMEA unit. 4. Set the unit’s serial port(s) to use NMEA In/ NMEA Out Interfacing with NMEA The unit allows for NMEA 0183, Version 3.01 output with a compatible GPS or navigation device. You must set the unit’s serial port(s) to NMEA In/NMEA Out to send data and receive data The SDDBT,SDDPT,SDMTW,SDVHW,SDWPL sentences are sent and received in NMEA 0183, Version 3.01. You can purchase complete information about National Marine Electronics Association (NMEA) format and sentences from: NMEA Seven Riggs Avenue SevernaPark,MD21146 USA Installing the Unit to a Garmin CANet GPSMAP 2008 is a CANet-compatible Garmin device, and can send or receive sonar information from another CANet-compatable Garmin device. Using the CANet optimizes the performance of CANet-compatible units, allowing sonar information from a Sounder or Fishfinder to be shared with up to two CANet compatible Garmin GPS units. A standard NMEA connection only allows depth, temperature, and speed GPSMAP® 2008/2108 Owner’s Manual insTalling The UniT information to be sent to a single GPS device, whe...
Эта инструкция также подходит к моделям:Эхолоты - GPSMAP 2008 (25.22 mb)