Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
2. Press [ENT] and move the ShuttlePoint knob to highlight TRIP LOG, press [ENT] or move the ShuttlePoint knob to the right. 3. A popup window will be shown with Nm (Nautical Mile), Sm (Statute Mile), Km (Kilometer) and RESET. Move the ShuttlePoint knob to select the desired units of measure and press [ENT] or move the ShuttlePoint knob to the right. Page 72 CPF180i and CPF300i 4. Press [CLR] or move the ShuttlePoint knob to the right until the selected page (Chart, Navigation, Highway or NMEA Data Page) is shown. 10.1.0 Resetting the Trip Log Select the page with TRIP LOG in one of the data windows as setup in the “Using the TRIP LOG” section. 1. Press and hold [MENU], move the ShuttlePoint knob to highlight TRIP LOG. 2. Press [ENT] or move the ShuttlePoint knob to the right to show a popup window, select RESET and press [ENT] or move the ShuttlePoint knob to the right. 3. A Warning popup window will be shown to confirm if you want to reset the Trip Log. Using the ShuttlePoint knob select YES and press [ENT]. The Trip Log is now reset. CPF180i and CPF300i Page 73 11. USER C-CARD The optional User C-CARD is used to back up Marks, Routes, and Tracks stored in your GPS Chart Plotter's memory. In the USA the User C-CARD is available directly from Jeppesen Marine at 800/424-2627. The User C-CARD is similar to a back up disk used with a PC, in case you have to clear the RAM to resolve an issue or load new software or if your CPF180i and CPF300i becomes stolen, or if you would like to transfer Waypoint, Track and Route information from one STANDARD HORIZON GPS Chart Plotter to another. 11.0 USER C-CARD MENU This optional card is similar to using a floppy disk on a PC to backup your files or to transfer the information that you have stored to a friends GPS Chart Plotter. The information shown below will assist you to transfer the User Points, Routes and Track history to the optional User C-CARD. 5621374 Time of file creation Date of file creation Type of data contained in the file (Mark file, Waypoint file...) Number of selected Slot File name Number of Selected file Information on stored User Points on Internal Memory 1234 Figure 11.0 - User C-CARD Menu 11.0.0 Formatting the User C-CARD 1. Press [MENU]. Move the ShuttlePoint knob to highlight USER POINTS and press [ENT]. 2. Move the ShuttlePoint knob to highlight USER C-CARD and press [ENT]. 3. Move the ShuttlePoint knob to highlight FORMAT and press [ENT]. 4. A popup Warning window will to confirm you want to format the User C-CARD. 5. Select YES and press [ENT] to confirm (select NO otherwise). The format of User C-CARD must be done before using a new User C-CARD: this operation prepares the User C-CARD to receive and store information. NOTE 567SAVE LOAD DELETE FORMAT CHANGE SLOT 1 FILE 1 MRKS 2 WPTS 5 RTES 1 TRKS 566 Formatting permanently erases all files previously saved on the User C-CARD. 11.0.1 Transferring files to the optional User C-CARD 1. Remove a C-MAP BY JEPPESEN NT+/MAX C-CARD if present and insert the optional CPF180i and CPF300i Page 75 User C-CARD into the slot. 2. Press [MENU]. Move the ShuttlePoint knob to highlight USER POINTS and press [ENT]. 3. Move the ShuttlePoint knob to highlight USER C-CARD and press [ENT]. 4. A screen will appear. Move the ShuttlePoint knob to the left to highlight SAVE and press [ENT]. 5. A popup SAVE FILE window will appear. In this window you can change the name and the file type by using the ShuttlePoint knob and pressing [ENT], when finished press [CLR] once. 6. To save the file to the User C-CARD. 11.0.2 Loading a file If you have a problem and accidentally loose the User Points in the GPS Chart Plotter with the optional User C-CARD it is possible to load the data back into the GPS Chart Plotter using the following procedure: 1. Press [MENU]. Move the ShuttlePoint knob to highlight USER POINTS and press [ENT]. 2. Move the ShuttlePoint knob to highlight USER C-CARD and press [ENT]. 3. Select the saved file from the User C-CARD list by using the ShuttlePoint knob and press [ENT]. 4. Move the ShuttlePoint knob to the left to highlight LOAD and press [ENT]. 5. A popup information window will appear when loading is complete. 6. Press [ENT] to confirm. 11.0.3 Deleting a file from the User C-CARD You may want to delete a saved file on the User C-CARD. 1. Press [MENU]. Move the ShuttlePoint knob to highlight USER POINTS and press [ENT]. 2. Move the ShuttlePoint knob to highlight USER C-CARD and press [ENT]. 3. Select the saved file from the User C-CARD list by using the ShuttlePoint knob and press [ENT]. 4. Move the ShuttlePoint knob to the left to highlight DELETE and press [ENT]. 5. A popup Warning window will to confirm you want to delete the file. 6. Press [ENT] to confirm. 11.0.4 Refreshing the User C-CARD You may want to change the User C-CARD inserted in the slot with a new one. 1. Press [MENU]. Move the ShuttlePoint knob to highlight USER POINTS and press [ENT]. 2. Move the ShuttlePoint knob to highlight USER C...
Эта инструкция также подходит к моделям:Эхолоты - MAX CPF180I (5.8 mb)
Эхолоты - MAX CPF300I (5.8 mb)
Эхолоты - MAX CPF300I (5.8 mb)