LISTED ALL TECHNICAL AND WARRANTY QUESTIONS: SHOULD BE DIRECTED TO THE LOCAL DEALER FROM WHOM THE WATER HEATER WAS PURCHASED. IF YOU ARE UNSUCCESSFUL, PLEASE WRITE TOTHE COMPANY LISTED ON THE RATING PLATE ON THE WATER HEATER. KEEP THIS MANUAL IN THE POCKET ON HEATER FOR FUTURE REFERENCE WHEN EVER MAINTENANCE ADJUSTMENT OR SERVICE IS REQUIRED. PRINTED IN THE U.S.A 1203 PART NO. 184639-000 SAFE INSTALLATION, USE AND SERVICE SAFE INSTALLATION, USE AND SERVICE Your safety and the safety of others is

Thread manifold to bottom of burner assembly (see Figure 9). Tighten with wrenches (see Figure 10.) 10. Temporarily connect hose and regulator to manifold. Connect hose and regulator to a 20 lb. propane cylinder. DO NOT LIGHT HEATER! Open propane cylinder valve. Leak test burner assembly and manifold connection using a noncorrosive leak detection fluid. DO NOT USE FLAME. See Checking for Leaks, page 8. When there is no sign of a leak, turn off propane/LP cylinder valve and disconnect regulator f

When ordering parts, follow the instructions listed under Replacement Parts, page 11. TD101A, TD111A TD103A TD109A KEY NO. PART NO. DESCRIPTION QTY. 1 118858-01 Table Top • 1 118858-02 Table Top • • 1 2 118866-01 Guard Rail • • • 3 3 118856-01 Deflector • • • 1 4 121525-01 Top Bracket • • • 3 5 121533-01 Upper Table Support Pillar • • • 3 6 121532-01 Lower Table Support Pillar • • • 3 7 118855-01 Table Decorative Grate, Mission • • 3 118855-02 Table Decorative Grate, Ornate • 3 8 118854-01 Deco

1. Keep heater clean. Remove any debris from ventilation openings. 2. Inspect heater before each use. Check connections for leaks. Apply mixture of liquid soap and water to connections. Bubbles forming show a leak that must be corrected. Correct all leaks at once. 3. Inspect hose/regulator assembly before each use. If hose is highly worn or cut, replace it immediately. At least annually, remove hose/regulator assembly from heater to inspect entire length of hose. 4. Spiders and insects can creat

Feet will install over raised areas underneath base weight. 3. Being careful not to scratch paint, lay cabinet base onto back side (use foam packaging block to support rear top of cabinet base). Align holes in bottom edges of cabinet base with holes in base as shown in Figure 4. Attach with 1 screw (C), 1 washer (D) and 1 nut (E) for each of the 9 holes (see Figure 4). Set assembly upright. 4. Attach base to weight with 4 screws (A) and 4 washers (B) as shown in Figure 4. 5. Install chain retain

What AMTROL Will Do If You Have a Covered Warranty Claim In the event of a breach of the foregoing warranty, AMTROL will at its option either make repairs to correct any defect in material or workmanship or supply and ship either new or used replacement parts or products. AMTROL will not accept any claims for labor, property damage or other costs. What This Warranty Does Not Cover - Exclusions and Limitations This Warranty does not cover any claim unless it was caused by a defect in material or

4.Zone valve does not open. 5.Electrical problems (relay, wiring, fuse, low voltage, brown-outs, etc.) 6.BOILER MATE™ scale build-up. 7.Clogged filter (if used) or clogged strainer in steam boiler systems. 1.a.Press reset button on boiler. b.Check main cut-off switch. c. Check fuse. 2.a.Check power supply. b.Check shaft coupling. c.Check impeller for locking. 3.Set BOILER MATE™ temperature to a higher setting. Call boiler service. 4.Check power supply. 5.a.Check fuse and replace. b.Check circuit

The BOILER MATE™ is intended to provide a tank service life of many years. Components, however, may be subject to failures that require service. Failure to use the correct procedures or parts in these circumstances may make the unit unsafe. Do not over-drain the tank. Improper thermostatic control could result during Step 6 and lead to damage to the BOILER MATE™. 6. Using a funnel, pour one gallon of commercial • DO NOT OPEN DOWN-STREAM FIXTURE IF YOU phosphoric acid solution (commercial icemake

THIS UNIT MUST BE INSTALLED AS A SEPARATE HEATING ZONE. DO NOT CONNECT THIS UNIT TO AN EXISTING HEATING ZONE OR FEED BOILER WATER DIRECTLY THROUGH THE COIL AS DANGEROUS OVER-HEATING WILL RESULT. DO NOT DRAIN THIS APPLIANCE BEFORE SHUTTING OFF THE SUPPLY VALVE AND OPENING THE RELIEF VALVE OR ANOTHER DOWNSTREAM FIXTURE, AS IT WILL DAMAGE THIS UNIT. ALSO, MAKE SURE A VACUUM BREAKER IS IN PLACE TO AVOID DAMAGING THE LINER. AVOID RISK OF INGESTING A TOXIC FLUID. THE HEAT TRANSFER MEDIUM SHOULD BE WAT

No stacking effect; greatly reduces static pressure at the roof line, reducing costly infiltration. With the comfort of warm floors, building is heated from floor up instead of from roof down. Low stack temperature 300° Reradiation from concrete mass results in even temperature throughout the building. Negative pressure at the perimeter of building allows for infiltration. High temperature or static pressure at the roof line increases heat transfer through roof. The higher the bay area, the high