FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE! RETAIN INSTRUCTIONS FOR FUTURE REFERENCE. DESCRIPTION The AirKing Oscillating Ceramic Heater features 2 heat settings and a fan only setting.The heater oscillates 120°and comes with a remote control for convenience. This unit also features a built in timer to allow up to 7.5 hours of operation before automatic shut- down and comes with a 6ft. (1.82m) 16/3 grounded cordset. SPECIFICATIONS Motor ...........

Remove upper shell (see page 8). 2. Remove filter end cover screws using 5/16" nut-driver. 3. Remove filter end cover and air filters. 4. Remove pump plate screws using 5/16" nut-driver. 5. Remove pump plate. 6. Remove rotor, insert, and blades. 7. Check for debris in pump. If debris is found, blow out with compressed air. 8. Install insert and rotor. 9. Check gap on rotor. Adjust to .003"/.004" if needed (see Figure 13). Note: Rotate rotor one full turn to insure the gap is .003"/.004" at tight

SAVE THESE INSTRUCTIONS 4 Rev. A 11/07 1 Rev. A 11/07 5084416 5084416 IMPORTANT INSTRUCTIONS - OPERATING MANUAL IMPORTANT INSTRUCTIONS - OPERATING MANUAL CEILING MOUNT INSTALLATION (Figures 1 and 2) NOTE: Distance mounted from the ceiling can be changed by using a length of 1-1/2” NPT pipe. Simply substitute your pipe for the provided threaded pipe. 1. Locate the Pipe Mounting Flange, securely mount to ceiling structure. Ensure ceiling structure can safely support the installed Fan. 2. Open one

One of each is shown in the illustrations below. 1. Install the Rear Grill onto the Motor, lining up the six holes in the grill with the six threaded holes in the Motor. Install (6) 10-32 X 5/16” Hex Screws through the Rear Grill into the Motor. Securely tighten all (6) screws. (Figure 3) 2. Push the Fan Blade onto the Motor Shaft, centering the Hub facing away from the motor, until it stops against the shaft. (Inset A) Align Square Head Bolt with flat of the Motor Shaft. TIGHTEN VERY SECURELY W

GRILL AND BLADE ASSEMBLY (Figures 3 and 4) NOTE: The assembly of the blade and grill is identical, regardless if the Fan has an oscillating motor or a non- oscillating motor. One of each is shown in the illustrations below. 1. Install the Rear Grill onto the Motor, lining up the six holes in the grill with the six threaded holes in the Motor. Install (6) 10-32 X 5/16” Hex Screws through the Rear Grill into the Motor. Securely tighten all (6) screws. (Figure 3) 2. Push the Fan Blade onto the Moto

com PARTS FOR DISCONTINUED, OBSOLETE AND CERTAIN OTHER PRODUCTS MAY NOT BE AVAILABLE. DUE TO SAFETY REASONS, MANY ELECTRONIC COMPONENTS AND MOST HEATER COMPONENTS ARE NOT AVAILABLE TO CONSUMERS FOR INSTALLATION OR REPLACEMENT. SAVE THESE INSTRUCTIONS 4 Rev. A 11/07 1 Rev. A 11/07 5084416 5084416 IMPORTANT INSTRUCTIONS - OPERATING MANUAL IMPORTANT INSTRUCTIONS - OPERATING MANUAL CEILING MOUNT INSTALLATION (Figures 1 and 2) NOTE: Distance mounted from the ceiling can be changed by using a length o

OSCILLATION ANGLE, FOR 45. OSCILLATION ANGLE, CONNECT THE OSCILLATION LINK TO THE INNERMOST HOLE IN THE CAM GEAR. (Inset A) 90. 45. 3. Cam Gear 1. 24” / 30” OSCILLATING CEILING MOUNT FAN MODEL 9324, 9335, 9374, 9375 (Inset A) 2. MAINTENANCE WARNING: ALWAYS UNPLUG THE CORD BEFORE MOVING OR SERVICING. WARNING: DO NOT IMMERSE FAN IN WATER! CLEANING: Use a soft cloth and mild soap solution such as liquid dish washing detergent. Dry all parts completely before reconnecting to power supply. CAUTION: D

2. Attach a Cable Clamp with the “U” on the tail side of the loop leaving a tail approximately 1 to 2 inches. Tighten Clamp Nuts. Make sure no part of the Cable interferes with the Blade. 3. Wrap the other end of the Cable around a secure building joist, truss, or other support near the Fan. Take up all excess slack in the Cable. CAUTION: USE ONLY THE MOUNTING HARDWARE WHICH IS RECOMMENDED FOR USE ON THIS FAN. 4. Attach the remaining Cable Clamp as indicated in Step 2. The excess tail should be

If they must be used, minimize the risk of overheating by ensuring that they are UL listed. Never use a single extension cord to operate more than one Fan. 11. Do not operate any Fan with a damaged cord or plug or after the Fan malfunctions, has been dropped or damaged in any manner. Return Fan to authorized service facility for examination, electrical or mechanical adjustment or repair. 12. Do not insert or allow fingers or foreign objects to enter any ventilation or exhaust opening as it may c

To Operate: Plug cord into a grounded 120V, 60 Hz outlet. Select desired operating speed with pull cord on the rear of the motor: First pull: High Second pull: Medium Third pull: Low Fourth pull: OFF NOTE: THIS FAN IS VERY HEAVY. Failure to securely hold onto head assembly while adjusting head angle could result in personal injury. 2. To adjust head angle: While holding head firmly, loosen knob under motor (turn counterclockwise). Tilt head to desired position FIRMLY retighten knob under motor.