Войти:
Оценок - 3, средний балл: 3.7 ( )

Инструкция по эксплуатации Desa, модель NON-OSCILLATING 9370

Производитель: Desa
Размер: 162.95 kb
Название файла:
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


GRILL AND BLADE ASSEMBLY (Figures 3 and 4) NOTE: The assembly of the blade and grill is identical, regardless if the Fan has an oscillating motor or a non- oscillating motor. One of each is shown in the illustrations below. 1. Install the Rear Grill onto the Motor, lining up the six holes in the grill with the six threaded holes in the Motor. Install (6) 10-32 X 5/16” Hex Screws through the Rear Grill into the Motor. Securely tighten all (6) screws. (Figure 3) 2. Push the Fan Blade onto the Motor Shaft, centering the Hub facing away from the motor, until it stops against the shaft. (Inset A) Align Square Head Bolt with flat of the Motor Shaft. TIGHTEN VERY SECURELY WITH AN ADJUSTABLE WRENCH. Failure to securely tighten the Bolt could result in damage to the Fan and/or personal injury. 3. Hold the Front Grill so that the name, in the center, is right side up and straight across. Starting at the top: Fasten Front Grill to Rear Grill by sliding the hooked wires on the Front Grill over the outermost ring on the Rear Grill. (Figure 4 / Detail A). The bottom most hooks will require the use of a flathead screwdriver to complete assembly. Stand behind the Fan. Slip the flat of the screwdriver between the Front and Rear Grills, next to one of the unfastened hooks. (Figure 4 / Detail B) Pull screwdriver handle upwards towards the Rear Grill. Slip the Front Grill hook over the Rear Grill outer ring with a push. Repeat procedure with remaining hooks. CAUTION: DO NOT BEND WIRES ON THE FRONT OR THE REAR GRILLS. Detail A Top Hooks Inset A Oscillating Motor View Detail B Bottom Hooks Motor Mounting Adapter Oscillating Motor Shown Non-Oscillating Motor Shown Figure 3 Figure 4 CAUTION: THE SECONDARY SUPPORT CABLE PROVIDED SHOULD BE USED ANYTIME THE CIRCULATOR IS MOUNTED OVERHEAD FOR ADDITIONAL SAFETY. secondary support cable (Figure 5) 1. Loop one end of Cable around the Large Guard Wires of both the Front and Rear Grills. 2. Attach a Cable Clamp with the “U” on the tail side of the loop leaving a tail approximately 1 to 2 inches. Tighten Clamp Nuts. Make sure no part of the Cable interferes with the Blade. 3. Wrap the other end of the Cable around a secure building joist, truss, or other support near the Fan. Take up all excess slack in the Cable. CAUTION: USE ONLY THE MOUNTING HARDWARE WHICH IS RECOMMENDED FOR USE ON THIS FAN. 4. Attach the remaining Cable Clamp as indicated in Step 2. The excess tail should be trimmed to extend 1 to 2 inches past the Clamp. 5. Check the Assembly to assure the Blade is free of all obstructions. CAUTION: Use of the secondary support cable does not guarantee protection against injury of persons, mounting of both the circulator and cable could fail if subjected to abuse, neglect or improper installation. Figure 1 Exploded View for Detail Large Guard Wires Set Screw Pipe Mounting Flange Inset Figure 2A Threaded Pipe Loctite 243 Non-Oscillating Motor View Motor Mounting Adapter Application Loctite 243 Figure 5 Set Screw Motor Mountin...

Эта инструкция также подходит к моделям:
Электрообогреватели - NON-OSCILLATING 9324 (162.95 kb)
Электрообогреватели - NON-OSCILLATING 9324 (162.95 kb)
Электрообогреватели - NON-OSCILLATING 9371 (162.95 kb)
Электрообогреватели - NON-OSCILLATING 9374 (162.95 kb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории