Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
Tighten the support arm bracket into place using the wing nuts provided. 6. For All Models Connect the POL fitting at regulator to the propane/LP cylinder by rotating the POL nut counter clockwise into the propane/LP cylinder's valve outlet and securely tighten with a wrench. WARNING: Attach heater in upright position. Never attach heater in a horizontal position. This could lead to dangerous flare-ups or fire. 7. Securely tighten all gas connections. 8. Open the cylinder's gas valve and check all connections for leaks. Apply mixture of liquid soap and water to gas joints. Bubbles forming show a leak that must be corrected. DO NOT USE A FLAME. TO START HEATER WARNING: When lighting the heater DO NOT look over top of heater (reflector). Stand to the side of the heater during ignition. Do not stand or have any part of your body in front of the heater. WARNING: MAKE SURE THERE IS NO OPEN FLAME IN THE AREA. Fully open the valve on the propane/LP cylinder. Read all lighting instructions before attempting to ignite heater. 1. Turn the heater regulator knob counterclockwise to the "HI" position. 2. Repeatedly push and release the piezo ignitor (dual burner), or place a lighted match near the face of the heating element (mesh screen) of the burner you are lighting, using the hole located on the side of the reflector. See Figure 6. CAUTION: Do not light at the orifice. 3. Depress the red button on the safety valve admitting gas to the burner (see Figure 6). WARNING:Donotdepressred valve button before repeatedly activating the piezo or inserting match. Figure 5 - Attaching Support Arm and Regulator to Propane/LP Tank Regulator Support Arm Bolt Support Arm Bracket Red Button on Safety Valve Figure 6 - Lighting Heater With a Match 113973-01C OPERATING INSTRUCTIONS MAINTENANCE AND Continued STORAGE 4. When the gas on the face of the mesh screen lights, continue to hold the valve button depressed for 30 seconds, then release. 5. If flame goes out, wait 5 minutes and repeat the lighting procedure. 6. If heater will not light after repeated tries, do not attempt to repair heater. Return heater to nearest authorized service center or to manufacturer of this product. 7. For dual burner models, repeat steps 1 through 4 to ignite the other burner. 8. After both burners or single burner, are lit, turn the heater regulator knob to the desired heat setting (LOW, MED, HI). TO STOP HEATER 1. Securely close valve on the propane/LP cylinder. 2. Turn the heater regulator knob to the "OFF" position. Wait 15 minutes for the heater to cool down before handling heater. 3. Always remove the heater from the propane/ LP tank after each use. Do not store the heater while attached to propane/LP tank. Remove the heater from the propane/LP tank by turning the fuel connector nut clockwise. Always store propane/LP tank outdoors. Never store propane/LP tank in an enclosed area. TO RESTART HEATER 1. Securely close valve at propane/LP cylinder. 2. Wait 5 minutes. 3. Restart following To Start Heater procedure, page 5. 1. Inspect heater before each use. Check connections for leaks. Apply mixture of liquid soap and water to connections. Bubbles forming show a leak that must be corrected. Correct all leaks at once. Have heater inspected at least annually by a qualified service person. 2. Before each use, check the soft "O" ring seat at the bullnose of the POL fitting. If the "O" ring is cut, scuffed, or otherwise damaged, replace it with part number 6681. 3. Inspect hose/regulator assembly before each use. If hose is highly worn or cut, replace. 3. Turn off the gas at the propane/LP gas supply cylinder when the heater is not in use. 4. When the heater is to be stored, the connection between the propane/LP gas supply cylinder and the heater must be disconnected and the cylinder removed from the heater and stored out of doors and in accordance with Chapter 5 of the standard for Storage and Handling of Liquefied Petroleum Gases ANSI/NFPA 58. 113973-01C SERVICING A hazardous condition may result if a heater is used that has been modified or is not functioning properly. When the heater is working properly: • The emmitter screen is glowing bright orang-red. • There are no flames above the burner. • The flame is burning on the surface of the screen and not inside the burner (flashback). • There is no strong disagreeable odor, eye burning or other physical discomfort. • There is no smoke or soot internal or external to the heater. • There are no unplanned or unexplained shut downs of the heater. The parts lists and exploded view show the heater as it was constructed. Do not use a heater which is different from that shown. In this regard, use only the hose, regulator and cylinder connection fitting (called a POL fitting) supplied with the heater. IMPORTANT: For this heater, the regulator must be set as shown in Specifications, page 2. If there is any uncertainty about the regulator setting, have it checked. TECHNICAL SERVICE A h...
Эта инструкция также подходит к моделям:Электрообогреватели - 000 BTU SPC-30R (3 mb)
Электрообогреватели - 000-15 (3 mb)