Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
Symptom of carbon monoxide poisoning can include headaches dizziness and difficulty in breathing. 1. Keep children and animals away from heater. 2. Never operate heater while sleeping or unattended. 3. Check the heater thoroughly for damage. Do not operate a damaged heater. 4. Do not modify the heater or operate a heater which has been modified from its original condition. 5. Use only propane/LP gas. 6. Use only vapor withdrawal propane/LP supply. If there is any question about vapor withdrawal, ask your propane/LP dealer. 7. For outdoor use only. Area must be well ventilated. Provide minimum openings of 1 sq ft (.093m.) near the floor and 1 sq ft. (.093m.) near the ceiling. Do not use inside house, camper, tent, vehicle, or any type of unvented or enclosed area. 8. Do not use heater in basement or below ground level. 9. Before connecting heater to the propane/LP tank, make sure the heater regulator knob is in the "OFF" position. Always connect and light heater in areas free of open flames. 10. Mount the propane/LP cylinders vertically (shutoff valve up). Secure them from falling or being knocked over and protect them from damage. 11. IMPORTANT: Use only the hose and regulator assembly provided with the dual burner tank top heater. Inspect the hose assembly before each use. If there is excessive abrasion or wear, or hose is cut, replace with hose assembly listed on parts list before using heater. The hose and regulator must be protected from damage. 12. The heater burner must be at least 2 ft. (.61m) above the floor. Always attach to propane/LP tank in an upright position. Never operate a heater on its side or attach to propane/LP tank in a horizontal position. This could lead to dangerous flare-ups or fire. Do not direct heat toward propane/LP cylinders. 13. Maintain minimum clearance from normal combustible materials (like paper) as follows: Sides -3 ft. (.91m); Top and Front - 5 ft. (1.5m). Locate 10 ft. (3m) from canvas or plastic tarpaulins or similar coverings and secure them to prevent flapping or movement due to wind action. 14. If at any time gas odor is detected, IMMEDIATELY DISCONTINUE operation until the source of gas has been located and corrected. 113973-01C 4 113973-01C Figure 3 - Attaching Burner Head Assembly to Support Arm 15. Install the heater such that it is not directly exposed to water spray, rain, dripping water and/or wind. 16. Operate only on a stable, level surface. 17. Due to the high surface and exhaust temperatures, adults and children must observe clearances to avoid burns or clothing ignition. 18. Do not move, handle or service while hot or burning. Do not attach or remove a hot or operating heater from the propane/LP tank. 19. Before each use, check heater for leaks. Never use an open flame to check for leaks. Apply a mixture of liquid soap and water to all joints. Bubbles forming show a leak. Correct all leaks. 20. Keep all connections and fittings clean. Make sure propane/LP tank valve is clean. Check "O" ring on heater inlet fuel valve connector for damage before each use. Replace if worn or damaged. 21. Use only in accordance with local codes or, in the absence of local codes, with the Standard for the Storage and Handling of Liquefied Petroleum Gases ANSI/NFPA 58 and CSA B149.1, Natural Gas and Propane Installation Code. ASSEMBLY INSTRUCTIONS 30,000 BTU MODELS ONLY 1. Inspect the heater components for possible shipping damage. If any is found, immediately notify the dealer. Check to make sure that all components are included with your heater (see pages 8 and 9). 2. Insert the piezo ignitor into the bracket on the burner support bracket as shown in Figure 1. Tighten the piezo mounting nut. Do not over tighten the nut. 3. Connect the burner hoses together as shown in Figure 2. Wrench tighten to insure leak tight connection. 4. Mount the burner assembly onto the support arm using the burner head mounting brackets and brass screws as shown in Figure 3. Place side of bracket into the slot on support arm. Secure with screw. Make certain that the air holes on the sides of the burner tube are not blocked. Securely tighten the burners into place. 5. Attach the electrode wires to the piezo ignitor as shown in Figure 4. SAFETY INFORMATION Continued Figure 1 - Installing Piezo Ignitor Piezo Ignitor Piezo Mounting Nut Burner Support Bracket Figure 2 - Attaching Burner Hoses to Regulator Burner Head Assembly Support Arm Burner Head Mounting Bracket Brass Screw Slot Air Hole Figure 4 - Attaching Electrode Wires to Piezo Ignitor Piezo Ignitor Electrode Wires OPERATING INSTRUCTIONS 1. Check heater for damage. If heater is damaged, promptly inform dealer where you bought heater. 2. Follow all of the safety and operating precautions. 3. Check the "O" ring on the POL before each use. Replace the "O" ring if there is any sign of wear or damage. 4. Make sure heater regulator knob is in the "OFF" position. 5. 30,000 Btu Models Only Attach the heater to the gu...
Эта инструкция также подходит к моделям:Электрообогреватели - AND TT15A 10 (3 mb)
Электрообогреватели - 000-15 (3 mb)