Оценок - 4, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
2. When facing the appliance, the remote receiver must be placed to the right of the gas valve and burner assembly. Notice: Do not let remote control receiver come in contact with burner assembly. On circulating vent-free firebox, install remote control receiver behind bottom louver. Refer to remote control installation and operating instructions for more details on remote control. 750 Millivolt System When you ignite the pilot, the thermocouple produces millivolts (electrical current) which energizes the magnet in the gas valve. After 30 seconds to 1 minute time period you can release the gas control knob and the pilot will stay ON. Allow your pilot flame to operate an additional one (1) to two (2) minutes before you turn the gas control knob from the PILOT position to the ON position. This time period allows the millivolts (electrical current) to buildup to a sufficient level allowing the gas control to operate properly. Millivolt Control The valve regulator controls the burner pressure which should be checked at the pressure test point. Turn captured screw counter clockwise 2 or 3 turns and then place tubing to pressure gauge over test point (Use test point “A” closest to control knob). After taking pressure reading, be sure and turn captured screw clockwise firmly to re-seal. Do not over torque. Check for gas leaks. VFSR Notice: (Wiring harness located in envelope) Connect the 2 - 1/4" terminals onto the TH and TH/TP terminals on valve. Place decorative log to right of the gas valve and burner assembly. When connecting to remote receiver, cut off 1/4" terminals from wires attached to ON/OFF switch. Strip wires back about 1/4". Connect stripped ends into remote receiver. VFSR Wiring Diagram (Figure 22) Figure 22 VFSV Wiring Diagram (Figure 23) Figure 23 VFSV Notice: (Wiring harness located in envelope) Connect black/red 3/16" terminal wire from receiver to 3/16" terminal on valve. Connect black 1/4" terminal wire from receiver to 1/4" terminal on valve. Install remote receiver cover over receiver when receiver is installed into fireplace area. Locate receiver and cover to the right and forward of valve. (Do not put receiver behind logs.) TROUBLESHOOTING SYMPTOMS - POSSIBLE CAUSES AND CORRECTION 1. When ignitor button is pressed, there is no spark at ODS/ pilot. a. Ignitor electrode positioned wrong - Replace pilot. b. Ignitor electrode is broken - Replace pilot. c. Ignitor electrode not connected to ignitor cable - Reconnect ignitor cable. d. Ignitor cable pinched or wet. Keep ignitor cable dry - Free ignitor cable if pinched by any metal or tubing. e. Broken ignitor cable - Replace ignitor cable. f. Bad piezo ignitor - Replace piezo ignitor. 2. Appliance produces unwanted odors. a. Appliance burning vapors from paint, hair spray, glues, etc. - Ventilate room. Stop using odor causing products while heater is running. b. Gas leak - Locate and correct all leaks. 3. Appliance shuts off during use. (Pilot and main burner are off.) a. Not enough fresh air is available for ODS/pilot to operate - Open window and/or door for ventilation. b. Low line pressure - Contact local gas company. c. ODS/pilot is partially clogged - Clean ODS/pilot. d. Defective thermocouple - Replace pilot. 4. Appliance shuts off during use. (Pilot stays on.) a. Low line pressure - Check line pressure to the valve. b. Defective thermopile - Check pilot flame, check wire connections, output should be a minimum of 325 millivolts across. TH/TP and TP terminals with ON/OFF switch off. 5. Gas odor even when control knob is in OFF position. a. Gas leak - Locate and correct all leaks. b. Control valve defect...
Эта инструкция также подходит к моделям:Вентиляторы - VFSM-18-3 (1.47 mb)
Вентиляторы - VFSR-16-3 (1.47 mb)
Электрообогреватели - VFSM-18-3 (1.47 mb)
Вентиляторы - VFSV-30-3 (1.47 mb)