Оценок - 2, средний балл: 3
(
)
)
|
Фрагмент инструкции
i • 6/09 B. Junction Box Installation Figure 9.2 Junction box installation JUNCTION BOX SIDEWALL JUNCTION BOX ACCESS SCREW PROVIDED Optional Accessories Connecting the electrical junction box is required if using a blower or remote. • Plug the cord into a convenient outlet. • An electrician may install an outlet box inside the fireplace. Place the outlet in the lower, back corner of the fireplace. • Must use cord supplied. CAUTION Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing. WARNING Shock hazard. • Replace damaged wire with type 105. C rated wire. • Wire must have high temperature insulation. Quadra-Fire • QVI30S, QVI35S • 340-901 Rev. i • 6/09 18 Quadra-Fire • QVI30S, QVI35S • 340-901 Rev. i • 6/09 Figure 9.4 Fan/Rheostat Wire Diagram NOTE: IF ANY OF THE ORIGINAL WIRE AS SUPPLIED WITH THE APPLIANCE MUST BE REPLACED, IT MUST BE REPLACED WITH TYPE 1050 C RATED WIRE. JUNCTION BOX VARIABLE SPEED CONTROL TEMPERATURE SENSOR SWITCH WHT GRN BLK BLK 110-120 VAC BLOWER BLK BLOWER RECEPTACLE BLK BLK BLK WHT GROUND WHT BLK BLK BLK FAN TEMPERATURE SENSOR SWITCH SPEED CONTROL (RHEOSTAT) JUNCTION BOX GROUND WIRE (ATTACH TO ANY METAL SURFACE) BEND UP TABS 110 Finishing A. Mantel Projections Figure 10.1 shows the minimum vertical and corresponding maximum horizontal dimensions of appliance mantels or other combustible projections above the top front edge of the appliance, not the surround. Figure 10.1 Clearances to Mantels or other Combustibles above Appliance MEASUREMENTS FROM TOP EDGE OF UNIT 12 in. MIN. 12 in. MAX. MANTEL EXHAUST VENT PIPE INLET AIR VENT PIPE Quadra-Fire • QVI30S, QVI35S • 340-901 Rev. i • 6/09 20 Quadra-Fire • QVI30S, QVI35S • 340-901 Rev. i • 6/09 Figure 11.1 Placement of Embers 11 Appliance Setup A. Remove Shipping Materials Remove shipping materials from inside or underneath the fi rebox. B. Clean the Appliance Clean/vacuum any sawdust that may have accumulated inside the fi rebox or underneath in the control cavity. C. Accessories Install approved accessories per instructions included with accessories. Contact your dealer for a list of approved accessories. Refer to Section 16. Shock or fi re risk. Use ONLY optional accessories approved for this appliance. • Using non-listed accessories voids warranty. • Using non-listed accessories may result in a safety hazard. • Only Hearth & Home Technologies approved accessories may be used safely. D. Ember Placement Explosion Risk. • Follow ember placement instructions in manual. • Do NOT place embers directly over burner ports. • Replace ember material annually. Improperly placed embers interferes with proper burner operation. Placing the Ember Material Ember material is shipped with this gas appliance. To place the ember material: • Embers CANNOT be placed directly over ports. • When placing Glowing Embers® onto the burner care should be taken so that the ports are not covered. Place the dime-size ember pieces near port holes in burner top, sides and front (see Figure 11.1). Failure to follow this procedure will likely cause lighting and sooting problems. • Place Mystic Ember over burner surface and around base of burner. Do not cover any burner port holes. Use this material to give the appliance a realistic ash bed. • Save the remaining ember materials for use during appliance servicing. The embers provided should be enough for 3 to 5 applications. WARNING WARNING EMBER MATERIAL/BRAISES .. E. Refractory Placement CAUTION: Refractory is fragile! Carefully remove the refractory from the packaging. Note: Refractory patterns and colors vary and may be different from the ones represented in the instructions. Step 1: Place the back wall refractory against the back wall of the unit. The cut-out will be over the pilot and air intake hole. On some models the refractory will be behind the pilot bracket (see Figure 11.2). Figure 11.2 Refractory Placement MODELS: Supreme-XT, Grand-XT, QVI30, QVI35, ADI60 Step 2: While holding the back wall in place, install the right side refractory. Bend down the small tab located on the top front edge of the firebox (see Figure 11.3). Figure 11.3 Step 3: Install the left side refractory in the same manner (see Figure 11.4). Figure 11.4 340-945B 6/02 Quadra-Fire • QVI30S, QVI35S • 340-901 Rev. i • 6/09 F. Positioning the Logs Log Set Assembly: LOGS-QVI30 If the gas logs have been factory installed they should not need to be positioned. If the logs have been packaged separately, refer to the following instructions. CAUTION: Logs are fragile! Carefully remove the logs from the packaging. 11 22 5544 33 66 77 PILOTPILOT BASEPANBASEPAN BURNERBURNER 11 11 Log #1 SRV340-701): Place log #1 in the back on the insert. Locate the legs of the log outside the 3/8” tabs to either side of the burner. Pull the log forward until the log is stopped by the back edge of the burner. The log should be centered. 340-935 2/02 Quadra-Fire • Q...
Эта инструкция также подходит к моделям:Электрообогреватели - QVI30S (3.62 mb)