Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
. Do not touch the circuitry on boards and soldered parts. Hold the metallic areas or the edge of the circuit boards. . Follow the safety instructions in the "Safety instructions" on page 31. 8.7.1 Required tools . Starting and completing the task: – key for the rack doors (if applicable) – Phillips Ph2 screw driver . Installing the expansion card: tool-less 148 Maintenance Manual RX900 S1 Expansion cards and BBU 8.7.2 Starting the task E Perform the following procedures: 1. "Opening the rack door" on page 40 2. "Shutting down the server" on page 41 3. "Sliding the server out of the rack" on page 42 4. "Removing the rear cover" on page 46 5. If applicable: "Mounting expansion card slot brackets" on page 107 6. If applicable: "Preparing the SFP+ transceiver module" on page 115 8.7.3 Removing the PCI Riser (if applicable) ...... Figure 82: Removing the PCI Riser E Press the green button (1). E Lift the handle (2) to disconnect the PCI Riser (PCIR) from the baseboard. E Pull the PCIR up and out by using the handle (3). RX900 S1 Maintenance Manual Expansion cards and BBU 8.7.4 Removing the slot cover ........ Figure 83: Removing the slot cover E Remove the slot lock by pulling the green handle upward (1), pushing the plastic part down (2) and lifting the slot lock (3). E Remove the slot cover (4). 8.7.5 Inserting the expansion card in the slot ...... Figure 84: Inserting the expansion card in the slot 150 Maintenance Manual RX900 S1 Expansion cards and BBU E Carefully insert the expansion card in the slot (1). E Insert the slot lock (2) and relock the slot (3). E If applicable, connect the cables on the expansion card. 8.7.6 Installing the PCI Riser (if applicable) .... Figure 85: Installing the PCI Riser E Carefully insert the PCIR in the slot (1). E Lock the PCIR by pushing down the handle (2). RX900 S1 Maintenance Manual Expansion cards and BBU 8.7.7 Completing the task E Perform the following procedures to complete the task: 1. "Installing the rear cover" on page 48 2. "Mounting the server in the rack" on page 49 3. "Bringing the server back to operation" on page 51 4. "Closing the rack door" on page 51 8.8 Removing a non-hot-plug expansion card Authorized personnel Authorized specialist personnel can carry out replacement tasks for integral server components. Ask you local Fujitsu service center for more detailed information. V CAUTION! Procedures indicated as "Authorized personnel only“ must be done by Fujitsu service personnel or technicians trained by Fujitsu for doing these tasks. Please note that unauthorized interference with the system will void the warranty and exempt the manufacturer from all liability. V CAUTION! . Before installing/removing expansion cards to/from the server, turn off the server, all peripheral devices, and any other connected devices. Also unplug all power cables from the power outlet. Failure to do so can cause electric shock. . The circuit boards and soldered parts of internal options are exposed and can be damaged by static electricity. Before handling them, first touch a metal part on the server to discharge static electricity from your body. . Do not touch the circuitry on boards and soldered parts. Hold the metallic areas or the edge of the circuit boards. . Follow the safety instructions in the "Safety instructions" on page 31. 152 Maintenance Manual RX900 S1 Expansion cards and BBU 8.8.1 Required tools . Starting and completing the task: – key for the rack doors (if applicable) – Phillips Ph2 screw driver . Removing the expansion card: tool-less 8.8.2 Starting the task E Perform the following procedures: 1. "Opening the rack door" on page 40 2. "Shutting down the server" on page 41 3. "Sliding the server out of the rack" on page 42 4. "Removing the rear cover" on page 46 RX900 S1 Maintenance Manual Expansion cards and BBU 8.8.3 Removing the PCI Riser (if applicable) ...... Figure 86: Removing the PCI Riser E Press the green button (1). E Lift the handle (2) to disconnect the PCI Riser (PCIR) from the baseboard. E Pull the PCIR up and out by using the handle (3). 154 Maintenance Manual RX900 S1 Expansion cards and BBU 8.8.4 Removing the expansion card from the slot ........ Figure 87: Removing the expansion card from the slot E If applicable, remove the cables from the expansion card. Remove the slot lock by pulling the green handle upward (1), pushing the plastic part down (2), and lifting the slot lock (3). E Carefully pull the expansion card out of the lot (4). RX900 S1 Maintenance Manual Expansion cards and BBU 8.8.5 Installing the slot cover ...... Figure 88: Installing the slot cover E Install the slot cover (1). E Insert the slot lock (2) and relock the slot (3). 156 Maintenance Manual RX900 S1 Expansion cards and BBU 8.8.6 Installing the PCI Riser (if applicable) .... Figure 89: Installing the PCI Riser E Carefully insert the PCIR in the slot (1). E Lock the PCIR by pushing down the handle (2). 8.8.7 Completing the task E Perform the following procedures to compl...
Эта инструкция также подходит к моделям:Компьютеры - PRIMERGY RX900 S1 (7.89 mb)