Оценок - 2, средний балл: 3
(
)
)
|
Фрагмент инструкции
Tighten 1/3 turn more using 5/8" socket wrench (4045 inch-pounds/4.5-5.1 n-m). 10. Attach nozzle assembly to burner strap. 11. Attach fuel and airline hoses to nozzle assembly. 12.Replace fan (see page 12). 13.Replace fan guard and upper shell. Nozzle (100/150 Models) 1. Remove upper shell (see page 12). 2. Remove fan (see page 12). 3. Remove fuel and air line hoses from burner head. 4. Remove spark plug cable from spark plug. 5. Remove spark plug from burner head using 13/16" open-end wrench. 6. Remove three (3) screws using 5/16" nut-driver and remove burner head from combustion chamber. 7. Place burner head into vise and lightly tighten. 8. Carefully remove nozzle from burner head by using 5/8" socket wrench (see Figure 26). 9. Blow compressed air through face of nozzle. This will free any dirt in nozzle area. 10.Inspect nozzle seal for damage. 11.Replace nozzle into burner head and tighten firmly (80-110 inch-pounds/ 9.1-12.4 n-m). Continued Figure 22 - Removing Air and Fuel Line Hoses, 35 Model Figure 23 - Removing Nozzle Assembly, 35 Model Fuel Line Fitting Fitting Figure 24 - Nozzle and Nozzle Adapter, 35 Model 15 100577 12. Attach burner head to combustion chamber. 13. Install spark plug in burner head. 14. Attach spark plug cable to spark plug. 15.Attach fuel and airline hoses to burner head. 16.Replace fan (see page 12). 17. Replace fan guard and upper shell. Pump Rotor (Procedure if rotor is binding) 1. Remove upper shell (see page 12). 2. Remove filter end cover screws using 5/16" nut-driver. 3. Remove filter end cover and air filters. 4. Remove pump plate screws using 5/16" nut-driver. 5. Remove pump plate. 6. Remove rotor, insert, and blades. 7. Check for debris in pump. If debris is found, blow out with compressed air. 8. Install insert and rotor. 9. Check gap on rotor. Adjust to .003"/.004" (.076-.101 mm) if needed (see Figure 29). Note: Rotate Rotor one full turn to insure the gap is .0037.004" (.076-.101 mm) at tightest position. Adjust if needed. 10. Install blades, pump plate, air filters. and filter end cover. 11. Replace fan guard and upper shell. 12. Adjust pump pressure (see page 13). Note: If rotor is still binding, proceed as follows. Continued 16 Nozzle Figure 26 - Removing Nozzle, 100/150 Models Figure 27 - Rotor Location, 35 Model Figure 28 - Rotor Location, 100/150 Models 100577 13.Perform steps 1 through 6 (see page 16). 14. Place fine grade sandpaper (600 grit) on flat surface. Sand rotor lightly in “Figure 8” motion four times (see Figure 30). 15.Reinstall insert and rotor. 16.Perform steps 10 through 12 (see page 16). SPECIFICATIONS Gap Adjusting Screw .003"/.004" (.076-.101 mm) Gap Measured With Feeler Gauge Figure 29 - Gap Adjusting Screw Locations Model Size Output Rating (Btu/Hr) Fuel Fuel Tank Capacity (U.S. Gal./Liters) Fuel Consumption (Gal. Per Hr/ Liters Per Hr) Nozzle Spray Angle Nozzle Spray Pattern Electric Requirements Amperage (Normal Run) Motor RPM Hot Air Output (CFM) 35 100 150 35,000 98,000 150,000 Use Only Kerosene or No. 1 Fuel Oil 3/11.3 9/34 13.5/51 .26/.98 .74/2.80 1.12/4.24 50° 60° 60° Solid Cone (All Models) 120 V/60 HZ (Same All Models) 1.7 3.2 4.4 1725 3450 3450 165 481 500 100577 17 WIRING DIAGRAMS Power Plug 120V/60Hz Figure 31 - Wiring Diagram, 35 Model Power Plug 120V/60Hz Figure 32 - Wiring Diagram, 100/150 Models 18 100577 ACCESSORIES Heater accessories and parts are available at your local dealer. HEAVY DUTY WHEELS AND HANDLE KIT For heavy duty applications. Makes your heatereven more portable and convenient. Fits 35 model. Order part number 00529-05. 19 100577 HOMELITE 1850 55TH Avenue Lachine (Quebec) H8T 3J5 Unit 212-214 590 Ebury Place Annacis Island New Westminister, B.C. V3M 6K7 595 Canarctic Drive Downsview, Ontario M3J 2P9 Homelite Homelite Canada Limited / Homelite Canada Limitée A Deere & Co. Affiliate / Une Filiale de Deere & Co. Homelite Pièce no. 18127-C Imprimé aux É-U CHAUFFERETTE PORTATIVE GUIDE DU PROPRIETAIRE \\ 1 \\ Modèles: HHC35A, HHC100A, et HHC150A IMPORTANT Assurez-vous d’avoir lu et compris ce guide avant de commencer à monter, utiliser ou réparer cet appareil. Une mauvaise utilisation de cet appareil pourrait causer des blessures graves. Gardez ce guide pour vous y reporter plus tard. NOTA: Se référer à la dernière page pour la succursale HOMELITE la plus rapprochée Cet appareil de chauffage est homologué par l’Association canadienne du gaz suivant les normes canadiennes B140.8-1967 et B140.0-1972. 100577-01 Rev. D 1/96 TABLE DES MATIERES INDEX_PAGE Notes sur la sécurité.......................................................................3 Nomenclature des pièces principales.............................................4 Déballage.......................................................................................5 Montage.......................................................................
Эта инструкция также подходит к моделям:Электрообогреватели - HHC100A (465.01 kb)
Электрообогреватели - HHC150A (465.01 kb)