Оценок - 3, средний балл: 4.7
(
)
)
|
Фрагмент инструкции
They are needed to safely operate this heater. Follow all local ordinances and codes when using this heater. To Start Heater 1. Fill fuel tank with kerosene or No. 1 fuel oil. 2. Attach fuel cap. 3. Follow all ventilation and safety information. Continued 8 100577 4. Plug heater’s power cord into approved, grounded, three-wire extension cord. Extension cord must be at least six feet (1.8 meters) long. Extension Cord Size Requirement 6 to 10 feet (1.8 to 3 meters) long, use 18 AWG (0.75 mm2) rated cord 11 to 100 feet (3.3 to 30.5 meters) long, use 16 AWG (1.0 mm2) rated cord 101 to 200 feet (30.8 to 61 meters) long, use 14 AWG (1.5 mm2) rated cord 5. Plug extension cord into standard 120 volt/60 hertz, 3-prong grounded outlet. Heater will start when extension cord is plugged into outlet. If not, push in heater’s flame-out control reset button (see Figures 6 and 7). Figure 7 - Flame-Out Control Reset Button, 100/150 Models To Stop Heater 1. Unplug extension cord from outlet. To Restart Heater 1. Wait two minutes after stopping heater. 2. Repeat steps under “To Start Heater”. Figure 6 - Flame-Out Control Reset Button, 35 Model Control Reset Button Flame- 100577 STORING, TRANSPORTING, OR SHIPPING PREVENTATIVE MAINTENANCE SCHEDULE Note: If shipping, transport companies require fuel tanks to be empty. 1. Drain fuel tank. Note: Some models have drain plug on underside of fuel tank. If so, remove drain plug to drain all fuel. If heater does not have drain plug, drain fuel through fuel cap opening. Be sure all fuel is removed. 2. Replace drain plug if provided. 3. If any debris is noted in old fuel, add 1 or 2 quarts of clean kerosene to tank, stir, and drain again. This will prevent excess debris from clogging filters during future use. 4. Replace fuel cap or drain plug. Properly dispose of old and dirty fuel. Check with local automotive service stations that recycle oil. 5. If storing, store heater in dry place. Make sure storage place is free of dust and corrosive fumes. IMPORTANT: Do not store kerosene over summer months for use during next heating season. Using old fuel could damage heater. _Awarning_ To avoid risk of burn and electrical shock, never attempt to service heater while it is plugged in, operating, or hot. Item Fuel tank How Often Flush every 150-200 hours of operation or as needed. How To See Storing, Transporting, or Shipping above. Air output and lint filters Replace every 500 hours of operation or once a year. See Air Output, Air Intake, and Lint Filters, page 12. Air intake filter Wash and dry with soap and water every 500 hours of operation or replace as needed. See Air Output, Air Intake, and Lint Filters, page 12. Fuel filter Clean twice a heating season or replace as needed. See Fuel Filter, page 13. Spark plug Clean and regap every 600 hours operation or replace as needed. See Spark Plug, page 14. Fan blades Clean every season or as needed. See Fan, page 12. Motor Not required/permanently lubricated 10 100577 TROUBLE- SHOOTING To avoid risk of burn and electrical shock, never attempt to service heater while it is plugged in, operating, or hot. OBSERVED FAULT Heater ignites, but flame-out control shuts off heater after a short period of time. POSSIBLE CAUSE Incorrect pump pressure Dirty air output, air intake and lint filters Dirty fuel filter Dirt in nozzle Dirty photocell lens Defective flame-out control REMEDY See Pump Pressure Adjustment, page 13. See Air Output, Air Intake and Lint Filters, page 12. See Fuel Filter, page 13. See Nozzle, page 15. Clean photocell lens. Replace flame-out control. . WARNING: Disconnect heater cord! Heater will not ignite, but motor runs for a short period of time. Incorrect pump pressure Carbon deposits on spark plug and/or improper gap Dirty fuel filter Dirt in nozzle Water in fuel tank See Pump Pressure Adjustment, page 13. See Spark Plug, page 14. See Fuel Filter, page 13. See Nozzle, page 15. Drain and flush fuel tank with clean kerosene. See Storing, Transporting, or Shipping, page 10. A WARNING: High voltage! Electronic ignitor not grounded ectronic ignitor Make sure electronic ignitor mounting is tight. Replace electronic ignitor. Motor hums when heater is plugged in, fan rotates slowly or does not turn. Solid state relay not allowed to reset Binding pump rotor Wait two (2) minutes before trying to restart heater. If fan is hard to turn, see Pump Rotor, page 16. Motor does not start; thermostat (if used) is set to call for heat. Motor thermal trip out Wait for motor to cool down. It will reset automatically. 100577 11 SERVICE PROCEDURES Upper Shell Removal 1. Remove screws along each side of heater using 5/16" nut-driver. These screws attach upper and lower shells together. 2. Lift upper shell off. 3. Remove fan guard. Fan IMPORTANT: Remove fan from motor shaft before removing motor from heater. The weight of the motor resting on the fan could damage...
Эта инструкция также подходит к моделям:Электрообогреватели - HHC100A (465.01 kb)
Электрообогреватели - HHC35A (465.01 kb)