Оценок - 5, средний балл: 4
(
)
)
|
Фрагмент инструкции
Do not substitute or use generic parts. Improper replacement parts could cause serious or fatal injuries. For more information, visit more information, visit 103385-01F 103385-01F 33 Forr morre iinfforrmattiion,, viisiitt PRODUCT IDENTIFICATION Figure 1 - Product Identification WARNING: Provide at least a 2.5 square foot opening of fresh, outside air while running heater. If proper fresh, outside air ventilation is not provided, carbon monoxide poisoning can occur. Provide proper fresh, outside air ventilation before running heater. UNPACKING 1. Remove all packing items applied to heater for shipment. Keep plastic cover caps (attached to valve inlet and hose/regulator assembly) for storage. 2. Remove all items from carton. 3. Check all items for shipping damage. If heater is damaged, promptly inform dealer where you bought heater. THEORY OF OPERATION The Fuel System: The hose/regulator assembly attaches to the propane gas supply. This provides fuel to the heater. The Ignition System: The piezo ignitor lights main burner. The Automatic Control System: This system causes the heater to shut down if the flame goes out. PROPANE SUPPLY You must provide propane gas and propane tank(s). Use this heater only with a propane vapor withdrawal supply system. See Chapter 5 of the Standard for Storage and Handling of Liquefied Petroleum Gas, ANSI/NFPA 58 and/or CAN/CGA B149.2. Your local library or fire department will have this booklet. This heater will operate with a 20-pound propane tank. However, you can only operate it in the LOW position during mildly cool weather. At higher heat settings or during colder weather, you must use larger tanks. The amount of propane gas ready for use from propane tanks varies. Two factors decide this amount. 1. The amount of propane gas in tank(s) 2. The temperature of tank(s) The chart below shows the minimum number of 100-pound tanks needed to run the heater. Connect tanks together with a manifold. Average Temperature (°F) Number At Tank Location Of Tanks 60° 1 40° 1 32° 1 20° 1 10° 2 0° 2 Less gas is vaporized at lower temperatures. Your local propane gas dealer will help you select the proper supply system. VENTILATION LO OFF HI MED Shell Ignitor Electrode Burner Tube Thermocouple Base Piezo Ignitor Button Valve Inlet Control Knob Hose/Regulator Assembly Top PRODUCT IDENTIFICATION UNPACKING THEORY OF OPERATION PROPANE SUPPLY VENTILATION 4 INSTALLATION OPERATION To Start Heater INSTALLATION WARNING: Review and understand the warnings in the Safety Information section, page 2. They are needed to safely operate this heater. Follow all local codes when using this heater. WARNING: Test all gas piping and connections for leaks after installation or servicing. Never use an open flame to check for a leak. Apply a mixture of liquid soap and water to all joints. Bubbles forming show a leak. Correct all leaks at once. 1. Provide propane supply system (see Propane Supply, page 3). 2. Connect fuel gas fitting on hose/regulator assembly to propane tank(s). Turn fuel gas fitting counterclockwise into threads on tank. Tighten firmly using a wrench. IMPORTANT:Tighten regulator with vent pointing down. Pointing vent down protects regulator from weather damage. 3. Connect hose to the valve inlet. Tighten firmly using a wrench. You must use the regulator supplied with heater even if propane tank has one. 4. Open propane supply valve on propane tank(s) slowly. Note: If not opened slowly, excess-flow check valve on propane tank may stop gas flow. If this happens, you may hear a click inside the regulator assembly, this is the check valve closing. To reset the excess flow check valve, close propane supply valve and open again slowly. 5. Check all connections for leaks. Apply mixture of liquid soap and water to gas joints. Bubbles forming show a leak that must be corrected. LO OFF HI MED Hose Valve Inlet Figure 3 - Hose and Valve Inlet OPERATION WARNING: Review and understand the warnings in the Safety Information section, page 2. They are needed to safely operate this heater. Follow all local codes when using this heater. TO START HEATER 1. Follow all installation, ventilation, and safety information. 2. Locate heater on stable and level surface. Make sure strong drafts do not blow on heater. 3. Make sure unit is turned off by slightly depressing and turning control knob fully clockwise to OFF. 4. Open propane supply valve on propane tank(s) slowly. Note: If not opened slowly, excess-flow check valve on propane tank may stop gas flow. If this happens, you may hear a click inside the regulator assembly, this is the check valve closing. To reset the excess flow check valve, close propane supply valve and open again slowly. Figure 2 - Regulator With Vent Pointing Down Propane Tank Propane Supply Valve Fuel Gas Fitting Hose Regulator Vent (pointing down) 6. Close propane supply valve.5. Slightly depress and turn control knob counterclockwise to the LOW ...
Эта инструкция также подходит к моделям:Электрообогреватели - 80 (1.48 mb)