Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
Place the heater on floor or other flat surface and insert plug into the proper wall outlet. WARNING ! BE CAREFUL NOT TO DIRECT THE AIRSTREAM AT DRAPERIES, FURNITURE, OR OTHER OBJECTS THAT COULD BE DAMAGED BY HEAT. DO NOT PLACE THE HEATER WHERE A SMALL CHILD MAY FALL OVER THE HEATER. DO NOT PLACE THE HEATER WHERE THE POWER CORD MAY BE WALKED ON, TRIPPED OVER, OR OTHERWISE SUBJECTED TO HARD USAGE. HEATER OPERATION Set thermostat to its full counterclockwise position. Plug the unit into a properly grounded 240 V outlet. (#6-20 for model 402A, #630 for models 482A & 562A). Set the thermostat to the farthest clockwise position. The fan should come on and the unit will start heating the room. When the room reaches comfort level, turn the thermostat counterclockwise until the heater turns off. The heater will cycle automatically around this preset temperature. To increase temperature, turn the thermostat knob clockwise. To lower temperature, turn the thermostat counterclockwise. CONTINUOUS FAN OPERATION (MODEL 562A ONLY) To activate the continuous fan feature, set rocker switch to “ON” position. The elements will continue to cycle on the thermostat setting. For no heat, turn thermostat to full counterclockwise position. With fan in “AUTO” position, fan will cycle with the thermostat. CLEANING AND STORAGE Turn thermostat off and remove plug from electrical outlet before cleaning heater. Use a soft cloth for dusting. For cleaning, use only a damp rag and non-abrasive dish detergent. Do not use abrasive chemical cleaners as these may harm the finish. If heater is used in very dusty location, use a vacuum cleaner dust brush to remove dust and other foreign material from the grilles. Always unplug cord and wrap around heater handle when not in use. Move heater to a safe location for storage. SERVICE This heater does not require any routine maintenance other than occasional cleaning to prevent clogging of intake grille opening. To clean air intake grille, use vacuum with brush attachment or high pressure air. The motor is permanently lubricated. Do not operate the heater with a damaged cord or plug or if the heater malfunctions or has been damaged in any manner. Return heater to authorized service facility for examination, electrical, or mechanical adjustment, or repair. Call the toll free number listed for assistance in locating the Marley authorized service center in your area. WARNING ! OPERATION OF THE SAFETY THERMAL LIMIT CONTROL INDICATES THE HEATER HAS BEEN SUBJECTED TO SOME ABNORMAL CONDITIONS. IT IS RECOMMENDED THAT THE HEATER BE CHECKED BY A REPUTABLE ELECTRICIAN OR REPAIR SERVICE TO INSURE THE HEATER HAS NOT BEEN DAMAGED. 5200-2274-003 ECR35081 12/01 NAMEPLATE MODEL AMPS DATE VOLTS PH Hz 482A WK/YY 240/208 1 60 20.0/17.3 MADE IN TAIWAN FOR: 2F68 MAX. MIN. LIMITED WARRANTY All products manufactured by Marley Engineered Products are warranted against defects in workmanship and materials for one year from date of installation, except heating elements which are warranted against defects in workmanship and materials for five years from date of installation. This warranty does not apply to damage from accident, misuse, or alteration; nor where the connected voltage is more than 5% above the nameplate voltage; nor to equipment improperly installed or wired or maintained in violation of the product’s installation instructions. All claims for warranty work must be accompanied by proof of the date of installation. The customer shall be responsible for all costs incurred in the removal or reinstallation of products, including labor costs, and shipping costs incurred to return products to Marley Engineered Products Service Center. Within the limitations of this warranty, inoperative units should be returned to the nearest Marley authorized service center or the Marley Engineered Products Service Center, and we will repair...
Эта инструкция также подходит к моделям:Электрообогреватели - 562A (119.75 kb)
Электрообогреватели - 482A (119.75 kb)