Оценок - 4, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Do not operate heater with a damaged cord or plug, or after heater malfunctions, or has been dropped or damaged in any manner. Discard heater, or return to authorized service facility for examination and/or repair. 11. WARNING Risk of Fire. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked. Heater must be kept clear of all obstructions: maintain a 3 foot minimum clearance from front and 12 inches from sides and rear. Heaters must be kept clean of lint, dirt and debris. (See Maintenance Instructions) 12. Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or relocatable power tap (outlet/power strip). 13. Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electrical shock, or injury to persons. 14. WARNING Risk of Fire. Do not use as a residential or household heater. SAVE THESE INSTRUCTIONS Tel: 360-693-2505 P.O. Box 1675 Vancouver, WA 98668-1675 Grounding Instructions Grounding Instructions This heater is for use on 240 (or 208) volts. The cord has a plug as shown to the right. No adapter is available for this blade configuration, and none should be used. The outlet type is a 240 (or 208) volt grounding outlet. When properly installed, it provides a ground connection through the cord to the heater to protect the operator from electrical shock. CGH402 – 20 AMP Receptacle ConfigurationPlug Configuration Installation Instructions CAUTION: Heater will operate on either 240 or 208 volts. Check heater voltage and phase on label on back of heater to make sure they are the same as the electrical service supplied. See plug configurations below. Altering the cord in any way will void the warranty! Be sure that the electrical receptacle is of the configuration and capacity appropriate for the heater. The heater may be used as a heavy duty portable. It may also be hung on the wall or ceiling using the bracket provided. The wall/ceiling mounting structure and anchoring provisions must be of sufficient strength to support the combined weight of the heater and mounting bracket. Specifications MODEL WATTS VOLTS (60 Hz) BTUs AMPS PLUG TYPE CGH402 4000/3000 240/208 13,648/10,236 16.7/14.4 20 Amp Operation and Maintenance How To Operate Your Heater 1. Turn the thermostat knob fully clockwise . 2. When the room reaches your comfort level, turn the thermostat knob counter clockwise until the heater shuts off. One or two minor adjustments may be necessary as the heat becomes better distributed throughout the area. 3. To reduce the room temperature, turn the knob counter clockwise . To increase the room temperature, turn the knob clockwise . Maintenance Heaters are equipped with a permanently lubricated motor and, therefore, no maintenance other than occasional cleaning is required. WARNING WHEN CLEANING OR DISSASEMBLING HEATER, BE SURE TO DISCONNECT HEATER CIRCUIT. To disconnect heater, turn thermostat to “OFF”, then remove plug from electrical outlet before cleaning or performing any maintenance. Allow heater to cool. IMPORTANT: Heater must be unplugged before performing any maintenance. For dusting, use a soft cloth. For cleaning, use only a damp rag and nonabrasive dish detergent. Do not use abrasive or chemical cleaners as these may damage the finish. If heater is used in a dusty location, use a vacuum cleaner dust brush to remove dust and other foreign particles from the grill. Always unplug cord and wind it around heater handles when not using. Keep heater in a safe location for storage. Any other servicing should be performed by an authorized service representative. Temperature Limiting Device All heaters are equipped with a thermally actuated manual reset limit control which automatically disconnects heating element and motor in the event normal operating temperatures are exceeded. If heater should fail to operate with thermostat turned clockwise to its limit, disconnect heater and wait a few minutes allowing heater to cool. Using a small straight object such as a pencil, push in button located inside small hole marked RESET. The thermal cutout almost invariably indicates a partial or complete blockage of the air intake or exit. Be sure to keep these areas clear in order to allow proper circulation of air. Warranty Maintenance: For more effective and safer operation and to prolong the life of the heater, read the Owner’s Guide and follow the maintenance instructions included with each heater. Failure to properly maintain the heater will void any warranty and may cause the heater to function improperly. Warranties are non transferable and apply to original consumer only. Warranty terms are set out below. LIMITED ONE-YEAR WARRANTY: Cadet will repair or replace any Cadet Garage/Utility Unit Heater (CGH) element or motor found to be defective within one year after the date of purchase. THESE WARRANTIES...