Оценок - 3, средний балл: 4 ( )

Производитель: Electrolux Размер: 1.24 mb Название файла: Язык инструкции:

Engine serial number: 6 CONTROLS Engine Switch To start and stop the engine. Switch position: OFF: To Stop the engine. Key can be removed/inserted. ON: To run the engine after starting. START: To start the engine by turning the starter motor. Return the key to the ON position once the engine has started. Do not use the starter for more than 5 seconds at a time. If the engine fails to start, release the switch and wait 10 seconds before operating the starter again. Recoil Starter To start the engine. Pull the starter grip lightly until resistance is felt. then pull briskly. NOTICE Do not allow the starter to snap Back against the engine. Return it gently to prevent damage to the starter. Fuel Valve The fuel valve is located between the fuel tank and carburetor. When the valve lever is in the ON position, fuel is allowed to flow from the fuel tank to the carburetor. Be sure to return the lever to OFF after stopping the engine. 7 Choke Rod The choke is used to provide an enriched fuel mixture when cold starting. The choke can be opened by moving the choke rod to the right and closed by moving the choke rod to the left. Circuit Breaker The circuit breaker will automatically switch OFF if there is a short circuit or a significant overload of the generator at the receptacle. lf the circuit breaker is switched OFF automatically, check that the appliance is working properly and does not exceed the rated load capacity of the circuit before switching the circuit breaker ON again. Ground Terminal The generator ground terminal is connected to the frame of the generator, on a metal non-current carrying part of the generator, and the ground terminals of each receptacle. Oil Alert System The Oil Alert system is designed to prevent engine damage caused by an insufficient amount of oil in the crankcase. Before the oil level in the crankcase can fall below a safe limit, the Oil Alert system will automatically shut down the engine (the engine switch will remain in the ON position). The QB1300 does not have this feature. Pilot Lamp The pilot lamp is illuminated when the generator is operating normally. DC Terminals The DC terminals may ONLY be used for charging 12 volt automotive type batteries. The terminals are colored red to identify the positive (+) terminal and black to identify the negative (-) terminal. The 8 battery must be connected to the generator DC terminals with the proper polarity (battery positive to generator red terminal and battery negative to the generator black terminal.) DC Circuit Protector The DC circuit protector automatically shuts off the DC battery charging circuit when the generator is overloaded, when there is a problem with the battery or the connections between the battery and the generator are improper. GENERATOR USE Connections to a Building’s Electrical System Connections for standby power to a building’s electrical system must be made by a qualified electrician. The connection must isolate the generator power from utility power, and must comply with all applicable laws and electrical codes. Improper connections to a building’s electrical system can allow electrical current from the generator to back feed into the utility lines. Such back feed may electrocute utility company workers or others who contact the lines during a power outage. Consult the utility company or a qualified electrician. Improper connections to a building’s electrical system can allow electrical current from the utility company to back feed into the generator. When utility power is restored, the generator may explode, burn, or cause fires in the building’s electrical system. In some areas, generators are required by law to be registered with local utility companies. Check local regulations for proper registration and use procedures. Generator Ground Circuits Portable generators have a system ground that connects the generator frame components to the ground terminals in the AC output receptacles. The system ground is not connected to the AC neutral wire. Local regulations, codes or laws may require that the ground system be connected to the AC neutral wire. If the generator is tested by a receptacle tester, it will not show the same ground circuit condition as for a home receptacle. If local regulations, codes, or laws require the system ground to be connected to the AC neutral wire, consult a qualified electrical or electrical inspector. Provide him with the electrical wiring diagram in this manual. The ground terminal can be used to ground the generator or bond the frame of the generator to the frame of a vehicle, but only if it is required by local law or electrical code. Before using the ground terminal consult a qualified electrician or electrical inspector for regulations in your area. AC Applications Before connecting an appliance or power cord to the generator make sure that it is in good working order. Faulty appliances or power cords can create a potential for electrical shock. If an appliance begins to operate a...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: