Оценок - 3, средний балл: 4 ( )

Производитель: Briggs & Stratton Размер: 846.53 kb Название файла: 97600.pdf Язык инструкции:

10 Insert and close the safety pins. 11 Remove the cap from the receptacle socket and connect the electrical plug. Note: Make sure the safety pins are properly installed before raising the mast. Test the Machine Functions By raising and extending, then retracting and lowering the mast back to the horizontal position, the following functions will be tested: winches, latches, mast extension and mast rotation. 12 Unlock the mast hold-down latch. 13 Turn the raise/lower winch handle clockwise until the mast raises approximately 2 feet / 60 cm. Result: A clicking sound should be heard as the winch handle is turned. 14 Release the winch handle. Result: The winch brake should hold when the handle is released. 15 Continue to turn the winch handle clockwise until the mast reaches full vertical position. Result: The mast should raise smoothly, free of hesitation or binding. Result: The spring latch on the front of the machine should lock the mast securely into place. 16 Turn the extend/retract winch handle clockwise until the mast extends approximately 2 feet / 60 cm. Result: A clicking sound should be heard as the winch handle is turned. Result: The mast sections should telescope smoothly, free of hesitation or binding. 17 Release the winch handle. Result: The winch brake should hold when the handle is released. Genie TML-4000 and TML-4000N Part No. 97600 Third Edition • Second Printing Operator's Manual 18 Press and hold the mast rotation lever. 19 Rotate the mast clockwise and then counterclockwise as far as it will go in either direction. Result: The mast should rotate smoothly and easily in both directions. 20 Rotate the mast back to its original position. Line up the black arrows on the front of the mast. 21 Release the mast rotation lever. 22 Attempt to rotate the mast in both directions. Result: The mast should not rotate. 23 Turn the extend/retract winch handle counterclockwise until the mast sections are fully retracted. Line up the blue arrows on the side of the mast. Result: No clicking sound should be heard when the winch handle is turned. 24 Pull and hold the mast release latch below the control panel. 25 Begin lowering the mast to the horizontal position by turning the raise/lower winch handle counterclockwise and holding the release latch open. Result: No clicking sound should be heard when the winch handle is turned. 26 Release the mast release latch and continue to crank the winch handle counterclockwise until the mast reaches horizontal position. Note: Make sure the mast is lowered completely into the transport cradle. Follow the mast stowing instructions in the Operating Instructions section to make sure the mast hold-down latch is securely locked. FUNCTION TESTS Test the Lights 27 Make sure the circuit breaker light switches are in the off position. 28 Start the engine. See Starting the Engine in the Operating Instructions section. 29 Turn all four circuit breaker light switches to the on position. Result: The lights should come on. Note: It can take up to 20 minutes for the lights to reach full intensity. If the lights are turned off and turned back on while they are still warm, they will not light up again for 20-30 minutes. Note: Make sure the circuit breaker light switches are turned off before shutting down the engine. Part No. 97600 Genie TML-4000 and TML-4000N Operator's Manual Third Edition • Second Printing Workplace Inspection Do Not Operate Unless: You learn and practice the principles of safe machine operation contained in this operator's manual. 1 Avoid hazardous situations. 2 Always perform a pre-operation inspection. 3 Always perform function tests prior to use. 4 Inspect the workplace. Know and understand the workplace inspection before going on to the next section. 5 Only use the machine as it was intended. Fundamentals The workplace inspection helps the operator determine if the workplace is suitable for safe machine operation. It should be performed by the operator prior to moving the machine to the workplace. It is the operator's responsibility to read and remember the workplace hazards, then watch for and avoid them while moving, setting up and operating the machine. Be aware of and avoid the following hazardous situations: · Drop-offs or holes · Bumps and obstructions · Debris · Slopes that exceed the machine’s leveling capability · Unstable or slippery surfaces · Overhead obstructions and high voltage conductors · Hazardous locations · Inadequate surface support to withstand all load forces imposed by the machine · Wind and weather conditions · The presence of unauthorized personnel · All other possible unsafe conditions Genie TML-4000 and TML-4000N Part No. 97600 Third Edition • Second Printing Operator's Manual Operating Instructions Do Not Operate Unless: You learn and practice the principles of safe machine operation contained in this operator's manual. 1 Avoid hazardous situations. 2 Always perform a pre-operation inspection. 3 Always perform function tests prior to us...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: