Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
Trimming You can use the trimmer to groom your sideburns and moustache. 1 Press the on/off button once to switch on the shaver. 2 Push the trimmer slide downwards to open the trimmer. ,You can now start trimming. 3 After trimming, close the trimmer and switch off the shaver. 4 Clean the trimmer (see chapter ‘Cleaning and Maintenance’). english 25 cleaning and maintenance Never use compressed air, scouring pads, abrasive cleaning agents or aggressive liquids such as petrol or acetone to clean the appliance. -Clean the shaver after ever y shave for optimal shaving performance. -Regular cleaning guarantees better shaving performance. -For the best cleaning results, we advise you to use the Philips Cleaning spray (HQ110). -Be careful with hot water. Always check if the water is not too hot, to prevent your hands from getting burnt. Note:Water may leak from the socket at the bottom of the shaver when you rinse it.This is normal and not dangerous because all electronics are enclosed in a sealed power unit inside the shaver. cleaning the shaving unit under the tap 1 Switch off the shaver and disconnect it from the mains. 2 Press the release button to open the shaving unit. 3 Rinse the shaving unit and hair chamber under a hot tap for 30 seconds. Be careful with hot water. Always check if the water is not too hot, to prevent your hands from getting burnt. -Rinse the hair chamber and the inside of the shaving unit. -Rinse the outside of the shaving unit. 4 Close the shaving unit and shake off excess water. Be careful not to hit the shaving unit against anything while shaking off excess water. 26 english Never dry the shaving unit and the hair chamber with a towel or tissue, as this may damage the shaving heads and the coupling spindles. 5 Open the shaving unit again and leave it open to let theshaver dry completely. cleaning the shaving unit with the cleaning brush 1 2 Switch off the shaver and disconnect it from the mains. Press the release button to open the shaving unit. 3 Pull the shaving unit off the shaver. 4 Turn the lock anticlockwise (1) and remove the retaining frame (2). 5 Remove and clean one shaving head at a time. Each shaving head consists of a cutter and a guard. Note: Do not clean more than one cutter and guard at a time, since they are all matching sets. If you accidentally mix up the cutters and guards, it may take several weeks before optimal shaving performance is restored. english 27 -Remove the cutter from the shaving guard and clean it with the brush. -Clean the inside and outside of the shaving guard with the brush. 6 Put the shaving heads back into the shaving unit. Note: Make sure that the projections of the shaving heads fit exactly into the recesses. 7 Put the retaining frame back into the shaving unit and turn the lock clockwise. 8 Insert the lug of the shaving unit into the slot in the top of the shaver (1).Then close the shaving unit (2). Note: If the shaving unit does not close smoothly, check if you have inserted the shaving heads properly and if the retaining frame is locked. 28 english cleaning the trimmer with the cleaning brush Clean the trimmer ever y time you have used it. 1 Switch off the shaver and disconnect it from the mains. 2 Push the trimmer slide downwards to open the trimmer. 3 Clean the trimmer with the short-bristled side of the cleaning brush. Brush up and down along the trimmer teeth. 4 Close the trimmer (‘click’). Tip: For optimal trimming performance, lubricate the trimmer teeth with a drop of sewing machine oil every six months. storage -Put the protection cap on the shaver after use to prevent damage and to avoid dir t accumulation in the shaving heads. english 29 Replacing the shaving heads For maximum shaving performance, we advise you to replace the shaving heads ever y two years.The shaving head symbol will light up to indicate that the shaving heads need to be replaced. Replace damaged shaving heads right away. Only replace the shaving heads with original HQ8 Philips Shaving Heads. 1 The shaving head symbol will light up orange continuously. 2 Switch off the shaver and disconnect it from the mains. 3 Press the release button to open the shaving unit. 4 Pull the shaving unit off the shaver. 5 Turn the lock anticlockwise (1) and remove the retaining frame (2). 6 Remove the shaving heads and place new ones in the shaving unit. Note: Make sure the projections of the shaving heads fit exactly into the recesses. 7 Put the retaining frame back into the shaving unit and turn the lock clockwise. 30 english 8 Insert the lug of the shaving unit into the slot in the top of the shaver (1).Then close the shaving unit (2). Note: If the shaving unit does not close smoothly, check if you have inserted the shaving heads properly and if the retaining frame is locked. 9 Press and hold the on/off button for 5 seconds and theorange light will go out. Accessories To retain the top performance of your shaver, make sure you clean it regularly and replace its shaving heads at the ...