Check their proper operation regularly. 2. Check bolts and screws for proper tightness at frequent intervals to keep the machine in safe working condition. Also, visually inspect machine for any damage and repair, if needed. 3. Before cleaning, repairing, or inspecting, stop the engine and make certain the impeller and all moving parts have stopped. Disconnect the spark plug wire and ground it against the engine to prevent unintended starting. 4. Do not change the engine governor settings or ove

1.5" 3" 8:1 8:1 10:1 Cast Aluminum Cast Aluminum Fabricated Steel 1/Tooled Steel 1/Tooled Steel 2/Hardened Chromium Steel 2/6 Steel 2/6 Steel 3/9 Cast Steel Formed Steel Formed Steel Cast Steel 24" 24" 24" Yes/On-board/7' Yes/On-board/7' No/Optional 2 Bushel Felt-lined 2 Bushel Felt-lined 3 Bushel Felt-lined 8" x 2" 8" x 2" 6" Casters-lockable Yes Yes Sleeve 8" x 2" 8" x 2" 10" x 4" Pneumatic Yes Drive Drive N/A N/A Yes Recoil Recoil Recoil 1.6 Quart 1.6 Quart 2 qt 20 oz 20 oz 2

Weight 200 lbs 220 lbs Warranty 2-Year Limited 2-Year Limited Chipper Shredder Vacuums Type Drive Chipper Capacity Debris Reduction Impeller Type Chipper Blades/ Material Shredder Flail Sets/Total # Material Shredder Screen Material Vacuum Width Vacuum Hose Bag Capacity Material Front Tires Bearings in Front Wheels Rear Tires Bearings in Rear Wheels Tamper Start Fuel Capacity Engine Oil Capacity Engine Approx. Weight Warranty * As rated by engine manufacturer. csv 060

Compare the illustrations in Figure 4 with your unit to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. Engine Controls See the Briggs & Stratton Owner/Operator manual packed with your unit. for the location and function of the controls on the engine. Starter Handle The starter handle is located on the engine. Pull the starter handle to start engine. See Figure 4. Spring Latch The spring latch is located on the top of the hopper.

Weight 200 lbs 220 lbs Warranty 2-Year Limited 2-Year Limited Chipper Shredder Vacuums Type Drive Chipper Capacity Debris Reduction Impeller Type Chipper Blades/ Material Shredder Flail Sets/Total # Material Shredder Screen Material Vacuum Width Vacuum Hose Bag Capacity Material Front Tires Bearings in Front Wheels Rear Tires Bearings in Rear Wheels Tamper Start Fuel Capacity Engine Oil Capacity Engine Approx. Weight Warranty * As rated by engine manufacturer. csv 060

This places the transmission in the correct position to take a “Cold” oil level reading. 3. Allow the tiller to rest in this position for at least five minutes for a “Hot” reading or two hours for a “Cold” reading. (Allow more time if the air temperature is below 40 °F). 4. Clean the area around the tine attachment dipstick so that no debris will fall into the transmission. 6-8: Tine attachment dipstick markings. 5. Using a 9/16-inch wrench, remove the dipstick as shown in Photo 6-7. Wipe th

Please come and visit us. te call your machine fhe PTO HORSE Model •BILT® Roto Tiller-Power Composter hout this Owner/Operator Manual and in r literature, we refer to your machine as the RSE Model”. The name aptly describes its se ruggedness, and it distinguishes this m the smaller ECONO-HORSE, PONY® and models, as well as from other models that n available in the past or that might be I in the future. tory dates back to the old Rototiller Corpo-5 company that introduced rear-tine rotary til

• Disconnect spark plug wire from spark plug and ground against the engine. • Remove the two wing knobs on each side of the discharge chute and lift the discharge chute up to keep it out of the way. See Figure 8. • Remove the two hairpin clips from each clevis pin which extend through the housing and remove the pins. • Remove the flail screen from inside the housing and clean the screen by scraping or washing with water. • Reinstall the screen, making certain to reassemble the flail screen with

NEVER put your hands inside the chipper chute — serious personal injury can resultl Short stubs of branches may be pushed through the chipper with the next branch. • If the engine slows down under load, reduce feed pressure and allow the engine to regain full speed before continuing. Overloading the chipper could result in damage to the belt or engine. NOTE: If the chipper is not cutting branches efficiently, the chipper blade could be dull, or the wood could be particularly hard. Try processi

This unit has been designed, engineered and manufactured to give you the best possible dependability and performance. Please carefully read this Manual. It tells you how to safely and easily assemble, operate and maintain your machine. Be sure that you and any other operators carefully follow the recommended safety practices at all times. Failure to do so could result in personal injury or property damage. Please complete and return the Owner Registration Card that is included in the literatur