Cap Screw 1 37 76934 S/16-18 x 3/4" Hex Hd. Cap Screw 4 38 76935 5/16-18 x 1-1/2" Hex Hd. Cap Screw 8 39 90194 5/16-18 Grip-Co Lock Nut 18 40 90692 5/16" Hatwasher 10 41 90391 5/16" Internal Lockwasher 4 42 90705 1/2" Flatwasher 2 43 90042 1/8 x 1-1/4" Cotter Pin 2 47 90636 5/16-18x1" Hex Hd. Cap Screw 2 48 40839 Hopper Lid 1 49 40840 1" Screen 1 50 40852 5/16-18x1" Milled Hd. Cap Screw 2 51 90598 1/4" Flat Washer 3 52 40853 1/4-20 Flex Lock Nuts Cap Pltd. 11 53* 40825 1 1/2" O.D.

Never lift the unit using the fuel tank for support. If the unit must be lifted , always use at least two people, and always grip the unit securely using the front leg and hopper handle. 2. If the unit must be tilted for transporting, consult the engine manual for required preparation. Normally, fuel and oil must be drained to prevent dangerous 4 fuel leakage, and unwanted transfer of the sump oil into the cylinder head area. 3. Always refill the oil sump with the recommended oil before attempti

Direct the shredder to discharge into a compost pile or against a wall, large board or other obstruction. Feed cornstalks by hand, slowly, several at a time until the last 18" remain in your hand - then let go. This willo give you a coarsely shredded product several inches long. With a garden spade or pitchfork refeed this material into the shredder until it reaches the consistency you want. A cornstalk that has been processed this way, just one time, will chemically break down within a day or t

Pull slowly at first and increase speed with each successive pull. 5. After the engine starts, open the choke and move the engine throttle control to SLOW. Warm up the engine by running it for at least a minute. 8. Set throttle to FULL and begin chipping/shredding. 10 Operation General Operating Safety Be sure to read all information in the Safety and Operation sections before attempting to operate this unit. Become familiar with all of the controls and how to stop the unit. Upon start-up and sh

Check each label to make sure it is still properly affixed to the chipper/shredder, and is still completely legible. If any label can’t be read or is missing, contact your local dealer for an immediate replacement. If you must use the unit without the label, review the label information in the “Safety Labels” section of this manual. Inspect Starter Rope/Handle The recoil starter rope and handle should be inspected for signs of abrasion or wear that could result in breakage. Don’t use worn out pa

Always wear safety goggles when operating the chipper/ shredder. Never allow anyone to operate the unit or remain in the immediate area unless they are wearing approved safety goggles. Proper Stance For Chipping Always maintain a stable, well-balanced stance to one side of the unit when operating the chipper/ shredder. Never stand directly in front of the chipper cone when performing chipping operations, since occasional kickbacks may occur, and result in you being struck by the tree limb or bra

Battery to Gound, 15” 15 1707056* 1 WIRE, Solenoid to Starter, 15” 16 1709086* 1 BOOT, Battery 17 1713945 1 FUELTANK 17A 1714020 1 CAP, Fuel Tank, vented 18 1714031* 1 SUPPORT, Battery 19 1714054* 2 KEYH Ignition Switch 20 1714055* 1 NUT, Ignition Switch 21 1714063 1 SUPPORT, Fuel Tank 22 1714093* 1 WIRING HARNESS 23 1714438* 1 TAB, Adapter 24 1916622* 3 NUT, Hex, 1/4-20 25 1916964* 3 LOCKWASHER, 1/4 26 1917356* 2 LOCKWASHER, 5/16 27 1920263" 2 NUT, Hex, E/16-24 28 1921332 2 CAPSC