Войти: n To access hidden keypad, pull up display cover. Select POWER, Source, then: n To set reference, push Abs/Rel and hold Set Ref for 3 seconds (3 buzzer sounds). n To display reference, hold Abs/Rel, so Ref flashes. n To stop / start display update, push Hold. n If a test tone is detected, meter will display Hz. AUTOTEST OPERATION ¦ No user action is required for meter to enter Autotest mode. n Autotest: Push Autotest on source and wait a few seconds. n Can also push Autotest on meter for faster
Replaceable Parts List Reference Designator Agilen Part Number Q'ty Description Model Mfr. P/N Mfr. Code E3614A 1 60W BENCH POWER SUPPLY -E3614A MODEL E3615A 1 60W BENCH POWER SUPPLY -E3615A MODEL E3616A 1 60W BENCH POWER SUPPLY -E3616A MODEL E3617A 1 60W BENCH POWER SUPPLY -E3617A MODEL E3614-60005 1 MAIN BODY ASSY 14 28480 E3615-60005 1 MAIN BODY ASSY 15 28480 E3616-60005 1 MAIN BODY ASSY 16 28480 E3617-60005 1 MAIN BODY ASSY 17 28480 0371-3806 1 KEY CAP -WHT ALL 28480 0371-8624 1 KEY CAP -GRA
Test Equipment Required The following Table A-1 lists the equipment required to perform the tests and adjustments of this section. You can separately identify the equipment for performance tests, calibration, and troubleshooting in the USE column of the table. Operation Verification Tests The following tests assure that the power supply is performing properly. They do not, however, check all the specified parameters tested in the complete performance test described below. Proceed as follows: A-2
You can set up the unit for remote operating modes by changing the settings of the rear panel switch and connecting the leads from the rear panel terminals to the load or the external voltage. Solid conductors of 0.75 to 1.5 mm2 can be connected to the rear panel terminals by simply push fitting. Thinner wires or conductors are inserted into the connection space after depressing the orange opening lever. Turn off the supply while making changes to rear panel switch settings or connections. This
Failure to comply with these precautions or with specific warnings elsewhere in this manual violates safety standards of design, manufacture, and intended use of the instrument. Agilent Technologies assumes no liability for the customer's failure to comply with these requirements. SAFETY SYMBOLS BEFORE APPLYING POWER. Verify that the product is set to match the available line voltage ! Instruction manual symbol; the product will and that the correct fuse is installed. be marked with this symbol
The protective action must not be negated by the use of an extension cord without a protective conductor. Warning: Any interruption of the protective conductor inside or outside the product or disconnection of the protective earth terminal is likely to make the equipment dangerous. Intentional interruption is prohibited. This product has been designed to be safe under the following environmental conditions: indoor use; altitude up to 2,000 meters; temperature range expanded to include 0 to +55 C
The 2 meter dc bias cable permits the amplifier to be remotely located, allowing it to be placed out of the way or where space is not critical. The 87421A is a 25 watt, ±12V dc power supply designed to power the Agilent 83006A, 83017A, 83018A, and 87415A microwave system amplifiers. A 2 meter cable is included for direct connection to the amplifier. • Designed specifically for Agilent Technologies microwave system amplifiers • Bias cable permits remote placement • Compact size for easy system in
Reproduction, adaptation, or translation without prior written permission is prohibited, except as allowed under copyright laws. © Copyright 2000 Agilent Technologies All Rights Reserved. Reproduction, adaptation, or translation without prior written permission is prohibited, except as allowed under copyright laws. Agilent Technologies Lightwave Division 1400 Fountaingrove Parkway Santa Rosa, CA 95403-1799, USA (707) 577-1400 Notice. The information contained in this document is subject to chang
Service Request Enable *SRE 128 Enables the OPER summary bit from the Status Byte register to generate RQS. Operation Condition STAT:OPER:EVEN? When you service the request, read the event register to determine that bit 10 (CC) is set and to clear the register for the next event. 1All bits of the PTR registers bits are set to 1 at power on or in response to STAT:PRES. Adding More Operation Events To add the CV (constant voltage) event to this example, it is only necessary to add the decimal valu
This bit (bit 7) is the logical OR of all the Operational Event register bits that are enabled by the Status Operation Enable register. Command Syntax STATus:OPERation:ENABle
