Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
176° F* Recommended hot water temp.: 120° -140° F* Hole size in mounting surface 1 3/8” Max. mounting surface depth: 1 5/8” 3/8” supplyhosesrequirestopswith3/8” compression fittings (not included) *Please know and follow all applicable local plumbing codes when setting the temperature on the water heater. Caution: Do not bend or twist the supply hoses! Installation Position the faucet and sealing ring in place on the mounting surface. From below the mounting surface, install the friction washer, metal washer and mounting nut. Tighten the mounting nut by hand. Tighten the tensioning screws. Install the pull rod. pull rod sealing ring friction washer metal washer mounting nut tensioning screw Connect the supply hoses to the stops with 3/8” compression fittings (not included). Use two wrenches, as shown in the diagram, to keep the supply hoses from twisting or becoming loosened from the faucet. Install the pop-up drain. Turn on the water. Check all connections for leaks. Reset the high temperature limit stop, if desired. Install the Pop-up Drain Remove the plunger assembly. Unscrew the drain outlet flange from the tee. Unscrew the tailpiece from the tee. Wrap the threads with plumbers’ thread tape and replace. Install the white, flexible sealing gasket to the flange. Place it in the sink outlet. From under the sink, install the black mack gasket, white friction ring and retainer nut to the flange. Do not tighten the nut against the bottom of the sink at this time. Thread the tee and tailpiece to the flange. The pivot must face the faucet. If necessary, turn the drain assembly. Tighten the retainer nut. Place the plunger assembly in the drain. Install the horizontal rod so that the end goes through the loop in the bottom of the height adjuster. Install and hand tighten the pivot ball nut. Attach the swivel connector to the end of the horizontal rod. Attach the swivel connector to the end of the pull rod. Position as desired and tighten with a small, flathead screwdriver. plunger flange sealing gasket mack gasket friction ring retainer nut horizontal rod height adjuster pivot ball nut swivel connector pull rod tee tailpiece Re-set the High Temperature Limit Stop (optional) Close the drain OR cover it with a wash cloth. Use the included 4 mm Allen wrench to push the screw cover into the handle. Retrieve the screw cover when the handle is removed. Use the 4mm Allen wrench to loosen the handle screw 4 complete revolutions. Remove the handle and put it in a safe place. Remove the decorative nut cover and put it in a safe place. Remove the handle screw from the stem of the cartridge. Remove the high temperature limit stop. Replace the high temperature limit stop so that the pin on the cartridge is in the desired slot on the limit stop. Note: the temperatures given in the diagram assume a water heater temperature of 140o F, a cold water temperature of 50o F and a water pressure of 45 PSI. Replace the decorative nut cover. Replace the handle screw. Use the Allen wrench to turn the screw 4 revolutions. Replace the handle. Finish tightening the handle screw. Turn on the water and test the faucet. User Instructions Pivot the handle out to turn the water on, in to turn the water off. Pivot the handle to the rear for warmer water, to the front for colder water. Replacement Parts 1 handle 32095000 1.1 screw cover 96338000 2 flange 97406000 3 nut 97209000 4 cartridge, assy 92730000 5 seal 95008000 6 aerator cpl. 94010000 7 ...
Эта инструкция также подходит к моделям:Сантехника - Talis S Single-Hole Lavatory Mixer with High Swing Spout 32070XX1 (715.44 kb)
Сантехника - Talis S Single-Hole Lavatory Mixer with High Swing Spout 32070XX1 (715.44 kb)