Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
• If you spill gasoline on your skin or clothing, change clothing and wash your skin with soap and water. REFUELING THIS SCOOTER HAS A 4-STROKE ENGINE AND REQUIRES UNLEADED 90 OCTANE OR HIGHER GASOLINE, WITHOUT METHANOL ADDITIVES. • Turn the engine OFF and allow the engine to cool at least two (2) minutes before removing the fuel cap. • The fuel cap is located at the rear of the scooter, behind the seat. To unlock the fuel cap, insert the ignition key and turn to the left (counter-clockwise). Remove the cap to add fuel. • Use UNLEADED 90 octane or higher gasoline without Methanol additives only. The tank holds 1.32 gallons (5 liters) of fuel. • DO NOT overfill the fuel tank. Fill tank to about 1.5 inches below the top of the tank to allow for fuel expansion. • Wipe up spills immediately. Gasoline may damage paint and plastic parts. Do not start the engine until the spilled fuel evaporates and the vapors have dissipated. • NEVER add anything to the gasoline in the fuel tank. • Replace the fuel cap securely. TIRE MAINTENANCE WARNING • DO NOT over-inflate the tire or underinflate the tires. The tires could slip off the wheel rims during braking, causing the scooter to become unstable and turn over in a curve. • To check the tire pressure, remove the cap from the valve stem and set aside. Use a tire pressure gauge to measure the air pressure in the tires. The correct pressure for the front tire is 26 PSI, and for the rear tire is 29 PSI. • Inspect the rims. If the rims are cracked or bent do not ride the scooter. They must be replaced. • Check the tires for wear and damage. If you notice cuts, punctures or excessively worn tread, the tire needs to be replaced. Contact your dealer for replacement parts and service. Routine Care and Maintenance, continued REAR DRUM BRAKE ADJUSTMENT • Test the rear brake lever free play. Apply light pressure to the left brake lever until you feel the brake engage. There should be very little free play between the “at rest” position of the brake lever and the applied position of the brake lever. Acceptable free play is between 3/8" and 3/4" (Fig. 1). Keep the brake cable adjusted to maintain acceptable free play. • Use a wrench to adjust the brake adjustment nut on the rear wheel (Fig. 2). Tighten as necessary until the correct freeplay is established. 2 Pivot PinPivot Pin2a 1 Between 3/8" and 3/4" BrakeAdjustment Brake NutAdjustment Nut NOTE: If you tighten the nut too much, the rear wheel will “drag”, even if the brake is not applied. • Make sure the brake adjustment nut is in the correct position after adjusting. The curved side of the nut must rest snugly against the pivot pin (Fig 2a). Check brake operation. CHECK REAR DRUM BRAKE SHOE WEAR • As the drum brake shoe linings wear, freeplay in the brake lever will increase. Each time the brake adjustment nut is tightened to decrease freeplay in the brake lever, the brake wear indicator will move to a position closer to the minus (–) sign (Fig. 3). • The indicator should never reach the minus sign. Brake shoes should be inspected and replaced by a QUALIFIED MECHANIC before the indicator reaches the minus sign. The brake shoe must be replaced before the lining reaches the minimum allowed thickness of 0.06" (1.5 mm). The brake drum must never measure larger than 3.892" (99.0 mm) in diameter. CHECK FRONT DISC BRAKE FLUID LEVEL • Locate the front brake master cylinder under the housing near the right handlebar (Fig. 4). If the fluid level in the window is at or below the low-level mark, take the scooter to your dealer for service. CHECK FRONT DISC BRAKE PAD WEAR • As the disc brake pads wear, the depth of the notches in the disc brake pads will decrease (Fig. 5). NOTE: The disc rotor has been removed for clarity in Fig. 5. The disc rotor is shown in place in Fig. 5a. • Never allow the notches to wear away completely. Brake pads should be inspected and replaced by a QUALIFIED MECHANIC while the notches are still visible. The brake pads must be replaced before the pads reach the minimum allowed thickness of 0.072" (1.85 mm). The minimum allowed thickness for the disc rotor is 0.118" (3.0 mm). WARNING • Never allow the front disc brake notches to wear away completely. • Never allow the rear drum brake pad indicator to reach the minus sign. • Even if working properly, the brakes should be inspected by your dealer at the intervals listed in the Professional Maintenance Schedule on page 17. 5 3 FRONT DISC BRAKEFRONT DISC BRAKE REAR DRUM BRAKEREAR DRUM BRAKE Time to replacebrake shoesTime to replace brake shoes Time to replacebrake shoeTime to replace brake shoe 4 Master Cylinder 5a Routine Care and Maintenance, continued CAUTION • Always allow the engine to cool before performing any routine maintenance. When hot, scooter parts can cause severe burns. ADDING ENGINE OIL • Oil should be checked every 300 miles (480 kilometers). • Stop on smooth, level ground, turn the ignition OFF and remove the key. • Use the center stand to park the scooter ...
Эта инструкция также подходит к моделям:Инвалидные коляски - 50GR06SV (1.36 mb)