Войти:
Оценок - 2, средний балл: 4 ( )

Инструкция по эксплуатации Invacare, модель 1095345

Производитель: Invacare
Размер: 177.25 kb
Название файла:
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


12. Insert one end of the insert tube into the front right hand side brace support. 13. Align mounting holes in the end of the insert tube with the brace support and secure with the EXISTING mounting screw and locknut. 14. Slide the outer tube over the insert tube as shown in DETAIL “B” of FIGURE 1. 15. Align the brace supports of the left hand side of the seat frame with the front and rear crossmembers. 16. Insert the front and rear crossmembers into the brace supports of the left hand side of the seat frame. Reinstall the two (2) EXISTING mounting screws and locknuts. 1 2 Contracture Assembly Insert Tube Washers Mounting Holes Mounting Screws Lock Nuts 2. Align the mounting holes of the contracture footplate assembly with two (2) desired mounting positions of the crossmember assembly. 3. Secure the contracture assembly to the crossmember assembly with two (2) mounting screws, washers and locknuts provided. Securely tighten. 4. If necessary, repeat STEPS 1-6 for the other contracture assembly. FIGURE 3 - REMOVING/INSTALLING THE CONTRACTURE ASSEMBLY - REVERSED MOUNT Installing the Contracture Assembly - Forward Mount (FIGURE 2) NOTE: Refer to the GENERAL WARNINGS and INSTALLATION WARNINGS in the SAFETY SUMMARY of this instruction sheet. NOTE: The number of mounting positions on the contracture assembly may vary due to the width of the wheelchair. 1. Align the mounting holes of the outer tube with the mounting holes of the insert tube of the crossmember assembly. Installing the Contracture Assembly - Reversed Mount (FIGURE 3) NOTE: Refer to the GENERAL WARNINGS and INSTALLATION WARNINGS in the SAFETY SUMMARY of this instruction sheet. 1. Remove the contracture footplate. Refer to CONTRACTURE FOOTPLATE HEIGHT ADJUSTMENT in this instruction sheet. 2. Align the mounting holes of the contracture footplate assembly with two (2) desired mounting positions of the crossmember assembly. 3. Secure the contracture assembly to the crossmember assembly with two (2) mounting screws, washers and locknuts provided. Securely tighten. 4. Reinstall the contracture footplate. Refer to CONTRACTURE FOOTPLATE HEIGHT ADJUSTMENT. 5. If necessary, repeat STEPS 1-4 for the other contracture assembly. Outer Tube Contracture Assembly Insert Tube Washers Mounting Holes Mounting Screws Lock Nuts Outer Tube FIGURE 2 - REMOVING/INSTALLING THE CONTRACTURE ASSEMBLY - FORWARD MOUNT Shoulder Screw Seat Frame (Rear) Bearing Housing Allen Screw Spacer Link Bracket Lower Seat Frame Base Frame Locknut Locknut Seat Frame DETAIL “A” Seat Frame Mounting Screws Lock Nuts Crossbrace (Rear) Insert Tube Outer Tube Brace Support Seat Frame Brace Support DETAIL “B” FIGURE 1 - INSTALLING THE CROSSMEMBER ASSEMBLY CONTRACTURE ASSEMBLY ANGLE ADJUSTMENT (FIGURE 4) NOTE: Refer to the GENERAL WARNINGS and INSTALLATION WARNINGS in the SAFETY SUMMARYof this instruction sheet. 1. Remove the mounting screw and locknut used to lock the angle adjustment of the contracture assembly. 2. Lift the contracture sup...

Эта инструкция также подходит к моделям:
Инвалидные коляски - 1095340 (177.25 kb)
Инвалидные коляски - 1095341 (177.25 kb)
Инвалидные коляски - 1095343 (177.25 kb)
Инвалидные коляски - 1095344 (177.25 kb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории