Оценок - 2, средний балл: 3
(
)
)
|
Фрагмент инструкции
If any parts are missing or if any damage is noted, immediately contact your Harmar Dealer. DO NOT attempt to install or use the lift with any missing or damaged parts. Models AL010and AL050 are packaged with a standard Class 2 hitch adapter. Model AL030 is packaged with a standard Class 1 flat bar style hitch adapter and stabilizer. If a different model hitch adapter or a Swing Away option is required, separate parts must be ordered. Vehicle Wiring Instructions BLACK WIRE BLACK WIRE OR Side mount Top mount Unwind the harness and lay it flat on the ground. One end of the harness has a black plug; this runs to the back of the vehicle. BEGIN ROUTING THE HARNESS AT THE VEHICLE BATTERY. Connect the black wire to the negative terminal of the battery. Do not connect the positive terminal yet. Run wiring harness under, or if possible, through the vehicle, using cable ties provided to secure the harness to the vehicle. Position the harness away from the fuel tank, exhaust system, brake and fuel lines and any possible pinch points. Harness should be positioned where it will not come in contact with any road debris. The harness may be too long for the vehicle. DO NOT CUT OR SHORTEN THE HARNESS. Use cable ties provided to coil excess wire and secure it to the vehicle frame.Rear plug should be secured even to the vehicle’s trailer hitch. Connect the red wire to the positive battery terminal. Wire in a standard 4-contact female flat trailer connector to the vehicle’s taililights. This will provide power for the motor cover light. TRAILER PLUG ON LIFT HARNESS MOTOR COVER LIGHT Ground for light is provided by main 2 prong power connector BROWN WIRE RED WIRE RED WIRE OR COIL EXCESS WIRE HERE RED WIRE RED WIRE OR Side mount Top mount XCESS WIRE HERE To back of vehicle To vehicle's battery RE Harness requires direct connection to vehicle battery. Do not connect harness to a secondary power source. Coil Excess Wire Here Hitch Adapters Bumper Mount ( Be sure to comply with vehicle's bumper rating ) CLASS 1 ( Flat Bar Style ) CLASS 2 ( 1.25 x 1.25 Solid Bar ) Omit stabilizer CLASS 3 ( 2 x 2 TUBE ) Refer to Section 4 or 5 for proper orientation ( right side up or upside down ) Determines lift's height from the ground PINCH BOLT SLEEVE FOR AL030 ONLY ( CLASS 1 ) Before installing an outside lift on your vehicle the vehicle must be equipped with the correct hitch. If you are unsure whether your vehicle has, or can accept a hitch, contact your local hitch installer or visit for vehicle hitch compatibility information. Please note, your lift comes equipped with a license plate hold light. To power this light vehicle must have a standard 4-contact trailer light harness. Contact your local hitch installer for more information. Trailer light wiring is designed to power license plate light ONLY. Attempting to run your lift from ANY secondary power sorce may cause your lift to operate poorly and could potentially cause damadge to the motor. All Harmar lifts must be wired directly to the vehicle battery. Hitch recievers MUST be installed so that it sits parellel to the ground. An improperly installed hitch can affect the operation of your lift. Some vehicles will require supension to be supplemented. Contact your local hitch installer or refer to your vehicle’s owners manual for further guidance. The following pages will help you to determine correct hitch adapter positioning. Installing the Lift Measure from Hitch Bar to ground 5-13" 13-15" 15-17" 17-19" OMIT STABILIZER OMIT STABILIZER HITCH POST HITCH ADAPTER To prepare your lift for installation you muct connect the lift to the Hitch Post and Hitch Adapter provided. Proper positioning is determined by the height of the vehicle hitch. 1. Measure the distance from the bottom of the hitch reciever on the vehicle to the ground. 2. Refer to Figure 1 below to determine correct placement of the hitch adapter. 3. Connect hitch post to lift. Figure 1 Once you have determined correct configuration, connect the Hitch Post to the Hitch Adapter following the diagram to the right using hardware supplied (1/2 - 13 x 3- 1/2” HHCS and lock nuts). Position the folded lift to the rear of the vehicle with the motor box folded away from the vehicle. With assistance, carefully lift the unit up to the Hitch Post and attach it using the 1/2” bolt, washers and lock nut provided. Installing the Lift With Swing Away Option Measure from Hitch Bar to ground 4-12" 12-14" 14-16" 16-17" Class I Hitch Adapter may NOT be used when installing a Swing Away. To prepare your lift for installation with a Swing Away you muct connect the lift to the Swing Away and Hitch Adapter provided. Proper positioning is determined by the height of the vehicle hitch. 1. Measure the distance from the bottom of the hitch reciever on the vehicle to the ground. 2. Refer to Figure 1 below to determine correct placement of the hitch adapter. 3. Connect hitch post to lift. Once you have determined correct configuration, connec...