Page 4 15997-0-0903 Do not cover any large rear ports with LS-18FA(C,O,S)-1 PHOTOS Photo 4Photo 3Photo 1 Photo 2loose material (glowing embers). 15997-0-0903 Page 5 Page 6 15997-0-0903 LS-24FA(C,O,S)-1 PHOTOS Photo 3 Photo 4 Photo 1 Photo 2Do not cover any large rear ports withloose material (glowing embers). LS-24FA(C,O,S)-1 PHOTOS Photo 3 Photo 4 Photo 1 Photo 2Do not cover any large rear ports withloose material (glowing embers). Page 715997-0-0903 LS-30FA(C,O,S)-1 PHOTOS Photo 3 Photo 4 Phot

(2.68kPa) for the purpose of input adjustment to a maximum of 14.0" w.c. (3.484kPa). *NOTE: Remote "RF" Models - 10.5" w.c. maximum Figure 7 25613-0-0309 Page 9 Page 10 25613-0-0309 Framing and Finishing 1. Choose unit location. 2. Frame in fireplace with a header across the top. It is important to allow for finished face when setting the depth of the frame. 3. Attach fireplace to frame using adjustable nailing flange. Preset depth to suit facing material (adjustable to 3/8", 1/2" or 3/4" depths

WARNING: This appliance is equipped for (natural or propane) gas. Field conversion is not permitted. 1 2 3 4 5 6 7 SASSAFRAS SUPER SIZE LOG PLACEMENT EMBER PLACEMENT LS-18RSS-1 PHOTOS Do not cover any large rear ports withloose material (glowing embers) Photo 1 Photo2 Do not cover any large front ports withloose material (glowing embers) . Page 5 Photo3Photo4SomelogshavebeenremovedforclaritySomelogshavebeenremovedforclarity 20171-3-0907 EMBER PLACEMENT LS-24RSS-1 PHOTOS Some logs have been remov

5. Compare the completed log installation with the appropriate photo from pages 7 through 9. Review previous steps to make any necessary adjustments. 6. Log placement is completed. PROPER INSTALLATION SEQUENCE: LS-16C-2 (Figure 1A) 1. Place rear (#4) log onto right, rear pin on rear log support. 2. Place middle (#1) log between rear log support and burner pan. 3. Place left, front (#2) log onto two (2) left, front pins on burner pan. 4. Place right, front (#3) log onto two (2) right, front pins

Consumer: Please retain these instructions for future use. Log sets comply with ANSI Z21.11.2 Unvented Heaters and also comply with ANSI Z21.60 Decorative Vented Appliances for Solid Fuel Burning Fireplaces. State or local codes may only allow operation of log sets in a vented configuration. Check your state or local codes. WARNING: If not installed, operated and maintained in accordance with the manufacturer's instructions, this product could expose you to substances in fuel or from fuel combus

3. The appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig (3.5 kPa). Attention! If one of the procedures results in pressures in excess of 1/2 psig (14" w.c.) (3.5 kPa) on the appliance gas valve, it will result in a hazardous condition. Page 14 25741-0-0309 25741-0-0309 Page 15 Over time, the rockwool will break down and new rockwo

15997-0-0903 Page 5 Page 6 15997-0-0903 LS-24FA(C,O,S)-1 PHOTOS Photo 3 Photo 4 Photo 1 Photo 2Do not cover any large rear ports withloose material (glowing embers). LS-24FA(C,O,S)-1 PHOTOS Photo 3 Photo 4 Photo 1 Photo 2Do not cover any large rear ports withloose material (glowing embers). Page 715997-0-0903 LS-30FA(C,O,S)-1 PHOTOS Photo 3 Photo 4 Photo 1 Photo 2Do not cover any large rear ports withloose material (glowing embers). LS-30FA(C,O,S)-1 PHOTOS Photo 3 Photo 4 Photo 1 Photo 2Do not c

Warning: ANY CHANGE TO THIS FIREPLACE OR ITS CONTROLS CAN BE DANGEROUS. Improper installation or use of the fireplace can cause serious injury or death from fire, burns, explosions, or carbon monoxide poisoning. Page 6 25613-0-0309 25613-0-0309 Page 7 Figure 1 LEFT SIDE VIEW FRONT VIEW RIGHT SIDE VIEW ELECTRICAL ACCESS VENT COLLAR TOP VIEW GAS LINE ACCESS A C J G I GAS LINE ACCESS H D E B VENT COLLAR STANDOFFS NAILING FLANGES GLASS FRAME ASSEMBLY GAS LINE ACCESS RATING PLATE AND LABELS GAS CONTR

See the dealer locator at To provide warranty service, your dealer will need your name and address, purchase date and serial number, and the nature of the problem with the unit. To Order Parts After the Warranty Period, please contact your dealer or one of the Master Parts Distributors listed below. This list changes from time to time. For the current list, please click on the Master Parts button at Please note: Master Parts Distributors are independent businesses that stock the most commonly or

See page 11 for Installing as a Vented Appliance. • Raise the mantel to the proper height. • Remove the mantel. Floor Clearance (Figure 6) If installing heater at floor level, the minimum distance to combustibles is “0” inches. Figure 4 If your installation does not meet the above clearances, you must proceed to one of the following steps: • Use a hood. • Operate the heater with flue damper open. See page 11 for Installing as a Vented Appliance. • Raise the mantel to the proper height. • Remove