Оценок - 2, средний балл: 5
(
)
)
|
Фрагмент инструкции
5. Compare the completed log installation with the appropriate photo from pages 7 through 9. Review previous steps to make any necessary adjustments. 6. Log placement is completed. PROPER INSTALLATION SEQUENCE: LS-16C-2 (Figure 1A) 1. Place rear (#4) log onto right, rear pin on rear log support. 2. Place middle (#1) log between rear log support and burner pan. 3. Place left, front (#2) log onto two (2) left, front pins on burner pan. 4. Place right, front (#3) log onto two (2) right, front pins on burner pan. 5. Compare the completed log installation with the appropriate photo from page 6. Review previous steps to make any necessary adjustments. 6. Log placement is complete. Attention: Do not use Figure 1 or Figure 1A to order replacement logs. Refer to Page 14 Parts List and Parts View to order logs for your appropriate model number. Apply loose material (glowing embers) per appropriate Installation Instructions and Owner's Manual. Replacement of loose material (glowing embers) must be purchased from Empire Comfort Systems, Inc. Application of excess loose material (glowing embers) may adversely affect performance of the heater. WARNING: All previously applied loose material must be removed prior to reapplication. Replacement Loose Material (glowing embers) Part Number Note: A single layer of embers is to be used when applying Platinum Bright Embers (alone or in combination with production embers) to the burner. Log Placement LS-(18,24,30)C2-1 Figure 1 Log Placement LS-16C-2 and CHBR Figure 1A The following WARNING applies when log set is installed onto an unvented gas burner assembly. WARNING: This appliance is equipped for (natural or propane) gas. Field conversion is not permitted. 1 2 3 4 LS-16C and CHBR 15998 LS-18C 15999 LS-24C 15970 LS-30C 15970 Platinum Bright Embers PE-20-1 CHARRED OAK LOG PLACEMENT EMBER PLACEMENT LS-16C-2 AND CHBR PHOTOS Photo1Photo2Donotcoveranylargerearportswithloosematerial(glowingembers). Do not cover any large front ports withloose material (glowing embers) Photo3Photo4 Page 6 20172-3-1006 EMBER PLACEMENT LS-18C2 PHOTOS Do not cover any large rear ports with Photo1Photo2loosematerial(glowingembers) Donotcoveranylargefrontportswithloosematerial(glowingembers) Photo3Photo4 20172-3-1006 Page 7 Do not cover any large rear ports withloose material (glowing embers) Photo 1 Do not cover any large front ports withloose material (glowing embers) EMBER PLACEMENT LS-24C2 PHOTOS Photo2 Photo4 Photo3 Page 8 20172-3-1006 Do not cover any large rear ports withloose material (glowing embers) Photo2Photo4EMBER PLACEMENT LS-30C2 PHOTOS Do not cover any large front ports withloose material (glowing embers) Photo1Photo3 20172-3-1006 Page 9 Page 10 20172-3-1006 Before you begin: Do not, handle these logs with your bare hands! Always wear gloves to prevent skin irritation. After handling logs, wash your hands gently with soap and water. All Logs The positioning of the logs is critical to the safe and clean operation of this heater. So...
Эта инструкция также подходит к моделям:Газовые нагреватели - LS-18C2-1 (8.35 mb)
Газовые нагреватели - LS-18C2S-1 (8.35 mb)
Газовые нагреватели - LS-24C2-1 (8.35 mb)
Газовые нагреватели - LS-24C2S-1 (8.35 mb)