LOG SET FOR UNVENTED GAS LOG HEATER MODELS VFP32FP(20,21,30,31)L(N,P)-1 VFP36FP(20,21,30,31)L(N,P)-1 EFFECTIVE DATE AUGUST 2006 — Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. — WHAT TO DO IF YOU SMELL GAS • Do not try to light any appliance. • Do not touch any electrical switch; do not use any phone in your building. • Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions. • If you

WARNING: Do not allow fans to blow directly into the fireplace. Avoid any drafts that alter burner flame patterns. WARNING: Do not use a blower insert, heat exchanger insert or other accessory not approved for use with this heater. Candles Avoid the use of scented or decorative candles while the fireplace is in operation. Candles produce a residue in the air that creates a soot like substance. Burning candles while the fireplace is operating magnifies the problem. It should be noted that candles

Figure 11a VENTING LABEL POWER EXHAUSTER PRESSURE SWITCH JUNCTION BOX FAN GUARD FAN MOTOR SIGHT GLASS GAS SUPPLY CONNECTION (Not Shown) ACCESS PANEL COMBUSTION AIR INLET COLLAR LIGHTING INSTRUCTION & RATING PLATE Figure 11b COMBINATION GAS CONTROL MANIFOLD PILOT PRESSURE TAP PRESSURE REGULATOR TUBING ADJUSTMENT SCREW (UNDER CAP SCREW) 12 Heater Parts from ACF Greenhouses 13 CHECKING INPUT RATE Pilot Orifice Identity Numbers Pilot Burner Identity No. Identity No. Manufacturer Natural Gas Propane

Maximum mounting heights higher versus units without outlet devises. Heater Parts from ACF Greenhouses 0.0 Static Air Pressure 0.1 Static Air Pressure 0.2 Static Air Pressure 0.3 Static Air Pressure Temp Sheave Sheave Sheave Sheave Model Input Rise Airflow RPM HP Drive Turns RPM HP Drive Turns RPM HP Drive Turns RPM HP Drive Turns No. Output (°F) (cfm) No. Open No. Open No. Open No. Open 40 938 635 1/4 C8 3.5 705 2 775 1 845 1/3 C1 4.5 45 833 560 0 645 1/4 C8 3.5 725 2 800 0.5 BAE 50,000 50 750

Warning: ANY CHANGE TO THIS FIREPLACE OR ITS CONTROLS CAN BE DANGEROUS. Improper installation or use of the fireplace can cause serious injury or death from fire, burns, explosions, or carbon monoxide poisoning. Page 6 25613-0-0309 25613-0-0309 Page 7 Figure 1 LEFT SIDE VIEW FRONT VIEW RIGHT SIDE VIEW ELECTRICAL ACCESS VENT COLLAR TOP VIEW GAS LINE ACCESS A C J G I GAS LINE ACCESS H D E B VENT COLLAR STANDOFFS NAILING FLANGES GLASS FRAME ASSEMBLY GAS LINE ACCESS RATING PLATE AND LABELS GAS CONTR

See the dealer locator at To provide warranty service, your dealer will need your name and address, purchase date and serial number, and the nature of the problem with the unit. To Order Parts After the Warranty Period, please contact your dealer or one of the Master Parts Distributors listed below. This list changes from time to time. For the current list, please click on the Master Parts button at Please note: Master Parts Distributors are independent businesses that stock the most commonly or

This opening must be large enough to provide a minimum 1” air space clearance from the vertical vent pipe to any combustible framing. 6. Install the Firestop/Thimble assembly to the framed opening in the ceiling using common nails or screws. Note: The thimble assembly is adjustable up or down as needed within the firestop. It is also designed with a pivoting firestop for use with 0 - 3/12 pitch cathedral ceilings. 7. To begin vent system assembly, first layout all the vent components on the floo

TO EXTEND VENT RUN, AN ADDITIONAL VENT EXTENSION KIT IS NECESSARY VENTING SUPPORT STRAPS (AS REQ’D) 35’ MAX CEILING ADJUSTABLE FIRESTOP/THIMBLE ASSEMBLY CLEARANCE TO COMBUSTIBLES REQUIRED FROM VENT PIPE ADJUSTABLE ROOF JACK ASSEMBLY STORM COLLAR DVVK-4FV DIRECT VENT TERMINATION KIT (cont.) Figure 36 25613-0-0309 Page 25 Vertical Flex Termination Kit Item Number Item Description Repair Part No. Quantity Supplied 1 4”/7” Vertical Termination Cap MF100038 1 2 Roof Support Kit MF100503 1 3 2 Ply Alu

See Figure 53. NOTE: Remove insulation from the framed area in the attic before installing the firestop and/or vent pipes. 25613-0-0309 Page 33 FRAMING AND FINISHING (continued) FRAMING AND FINISHING (continued) EXISTINGCEILINGJOISTSNEWFRAMINGCEILINGBELOWBANAILS,4REQUIREDCEILINGFIRESTOPAB Vent Size A B 6 5/8" 10" 10" 8" 10 1/2" 10 1/2" Vent Size A B 6 5/8" 10" 10" 8" 10 1/2" 10 1/2" Figure 51 Figure 53 ABNAILS,4REQUIREDCEILINGFIRESTOPSee Horizontal Termination Page 35 and Vertical Termination Pa

(2.68kPa) for the purpose of input adjustment to a maximum of 14.0" w.c. (3.484kPa). *NOTE: Remote "RF" Models - 10.5" w.c. maximum Figure 7 25613-0-0309 Page 9 Page 10 25613-0-0309 Framing and Finishing 1. Choose unit location. 2. Frame in fireplace with a header across the top. It is important to allow for finished face when setting the depth of the frame. 3. Attach fireplace to frame using adjustable nailing flange. Preset depth to suit facing material (adjustable to 3/8", 1/2" or 3/4" depths