x1 Va) 50 4647-30 Frame Catcher—Upper 9 2651-49 Belt (3/8 Round Sect.) 51 0773-13 Basket—Fabric 10 1632-229 Shaft—Brush Drive (Short) 52 1513-87 Bolt—Shoulder (Pivot) 11 1650-21 Ring—Retainer *53 1538-13 Nut (3/8-16 Hex Lock) 12 1540-17 Washer—Flat (5/8x15/16 54 2603-77 Brace—Frame X1/16) 55 4709-24 Panel—Catcher Bottom 13 2632-231 Shaft—Brush Drive (Long) *56 1095 Screw (10-32x1/2 Philips) 14 4703-24 Baffle—Top 57 1694-26 Clamp *15 1507-12 Screw (10-32 x 1 -1 /8 Sems) *58 1507-6 Bolt

Split) 31 1025 Washer—Lock (5/16 Split) 75 1632-228 Shaft—Impeller (Short) 32 1671-1 Pawl 76 2632-230 Shaft—Impeller (Long) 33 2692-6 Pinion R.H. 77 1530-1 Rivet—(3/16.Dia. x 114 Truss 34 2692-7 Pinion L.H. Hd.) 35 3108-148 Assembly—Wheel 78 1540-81 Washer (17/64 x 3/4x1 /16) 36 4636-18 Wheel—Gear & Rim 79 4697-15 Draw & Bar—Front (L.H.) 37 1652-52 Bushing 80 1509-38 Bolt (10-32x3/8 Hex Hd.) 38 3619-58 Tire 81 1543-69 Washer (21 /64 x 3/4 x 3/32 *39 141 Washer (3/8x7/8x3/16) Nylon)

After the desired clearance is obtained allow the adjust lever to spring back locking the trunnion in the proper positioning hole. Follow the same procedure for the opposite wheel. See figure 1. 2 LUBRICATION Figure 1 DUMPING OF SWEEPER Your sweeper can be dumped very easily without removing or disconnecting a part. Simply lift the hopper as shown and swing it over the sweeper and dump. See figure 2. A CAUTION If you are planning on dumping your Sweeper near a fire use care not to get t

19468-6 19468-7 TM0-285A 197-468A and 63584 Important: Read Safety Rules and Instructions Carefully TRAIL SWEEP • 0 PRINTED IN U.S.A. FORM NO. 770-6647 REV. 7-76 I ASSEMBLY Your Two-Stage Sweeper has been assembled at the factory except for the Front Draw Bar Assembly and the Hopper which has been shipped in the storage position. To assemble, slide the Front Draw Bar onto the Rear Draw Bar as shown and fasten securely with nuts and bolts provided. To prepare the Hopper for operation, r

See figure 2. A CAUTION If you are planning on dumping your Sweeper near a fire use care not to get too close, the brushes can be destroyed by excessive heat or flame. The bearings in your Sweeper have been prelubricated at the factory, however, it is recommended that a few drops of light oil should be added to the impeller and brush shaft bearings twice a year. Also, the wheels and pinions should be removed, the axles cleaned and an even coat of light oil applied. See figure 3. Bearing Fi

770-7212J I CONTENTS OF HARDWARE PACK/LOOSE PARTS IN CARTON в- cf K-ÎÎ N—f ffÎÎÎff i °рц§ 0 (May Be Assembled) Q--ÎÎÎÎÎÎTÎ11 R- CONTENTS OF HARDWARE PACK (See figure 1): (Hardware pack may contain extra items which are not used on your unit.) Group A—Discharge Chute Tube Assembly FIGURE 1.—Contents of Hardware Pack A (5) Hex Bolts 1/4-20 x 5/8" Long В (3) Spring Washers 1/4" I.D. С (5) Hex Lock Nuts 1/4-20 Thread D (2) Retainer Clips E (3) Retainer Straps Group B—Grass Collec

See figure 9. The large holes in the support tube mounting brackets go to the left side of the unit. The flange in the brackets go toward the top. c. Secure with hex bolts (N), lock washers (O) and hex nuts (P), finger tight only. After all eight hex bolts and nuts are assembled, then tighten securely. NOTE: It may be necessary to spread the support brackets slightly in order to align the holes. 30" & 32" Decks 36", 38", 42" & 46" Notch Latch Support Bracket Support Tube Mounting Bracket

READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE \OUR POWER VACUUM. FAILURE TO COMPLY WITH THESE INSTRUC- Æj TIONS MAY RESULT IN PERSONAL INJURY. WHE N YOU SEE THIS SYMBOL- ^ HEED ITS WARNING. A Your power vacuum was suilt to be operated according to the rules for safe operation in this manu- DANGER: al. As with any type of po ver equipment, carelessness or error on the part of the operator can result in serious injury. If you vi< »late any of these rules, you may c

A 4 oz. plastic bottle of light oil lubricant is available. Order part number 737-0170. Engine oil may also be used. ENGINE Refer to the separate engine manual for engine maintenance instructions. Maintain engine oil as instructed in the separate engine manual packed with your unit. Read and follow instructions carefully. Service air cleaner every 25 hours under normal conditions. Clean every few hours under extremely dusty conditions. Poor engine performance and flooding usually indicates t

After assembly, service engine with gasoline and oil as instructed in the separate engine manual packed with your unit. Upper Handle >v. Hex Bolt 3/4" . ,L?*?9 u Hex Bolt 1-1/2"' Lock Washer L Hex Nut Cupped Washer,, FIGURE 2. HSXNUt FIGURE 3. Axle-1 Shaft Flat Washer NOTE: Reference to right or left hand side of the vacuum is observed from behind the unit in the operating position. TOOLS REQUIRED FOR ASSEMBLY (2) 9/16“ Wrenches (2) 7/16" Wrenches (1) Hammer or Rubber Mallet UNPACK