Оценок - 3, средний балл: 4.3 ( )

Производитель: Homelite Размер: 553.34 kb Название файла: Язык инструкции:

Insert the other end of the spring through the hole in the end of the hook. Then place the hook over the lip on the front of the dump cart body (Figure 9). Mounting the Roving Nozzle The roving nozzle attaches to the blower inlet in place of the hose from the mower. For storage a rack is provided for installation on the front of the dump cart (Figure 12.) 1. Install the hose flange and a hose clamp on the plain end of the hose. Secure with one 1/4-20 x 3" machine screw, lockwasher and hex nut (Figure 4). 2. Install the hose handle clamps the desired distance from the pickup end of the hose and attach the handle. (Figure 13). 6 3. Attach the flanged end of the roving nozzle to the blower housing, seating the flange fully in the slots (Figure 4), 4. The storage rack is assembled and hung on the front of the cart. No hardware for mounting is required. (Figure 14). 1. Check to insure that the hoses are securely fastened to the blower housing, mower adapter and trailer cover sleeve. 2. Ground speed and throttle .adjustment for the vacuum collector will vary according to the type of work being done. When making a shallow cut of fairly dry grass, a faster ground speed (third or fourth gear on manual transmission tractors) and lower throttle setting can be used. When collecting wet, thick or heavy material, use a slower ground speed (first or second gear on manual transmission tractors) and run the engine at near full or full throttle. This will produce increased vacuum. 3. When picking up leaves and tall grass, raise the mower to the highest cutting position. A second pass can then be made with the mower at a lower setting to complete the job. 4. In wet and extremely high grass, it may be necessary to pick up only half of the mower width to prevent the hoses from becoming clogged with grass. 5. Periodically check the hoses and blower housing to in-,sure grass clippings have not accumulated which will affect the flow of grass to the dump cart. 6. Unzip the zipper on the canvas cover during normal operation to provide an air release in the cart enclosure. During some operations it may be desirable to have the zipper in the half closed or fully closed position. 7. After using, clean out grass in neck of hose and dump cart. Caution: Before disconnecting any hoses or performing any maintenance or adjustment work, be sure that the tractor engine is off and the tractor parking brake is engaged. Do not operate unit if either one or both hoses are not connected to the blower assembly. Trouble Shooting If leaves and grass are not being picked up, check the following: 1. Run the engine at full throttle and use a stow ground speed (first gear or manual transmission tractors). 2. Check all hose connections to be sure they are tight. 3. Check hoses and blower housing to be sure they have not become plugged with grass or leaves. If the hoses become plugged, check the following: 1. Grass may be too high or wet, use only half the mower width. 2. Use a slow ground speed and run the engine at full throttle (first gear on manual transmission tractors). 3. Raise the mower to full height for the first pass, lower it to make a second pass. After each use Be sure to cleán out the hoses and cart thoroughly, especially at the cover sleeve connection. Storage Remove the door on the high capacity cart cover or the entire low profile cover and place it where air will circulate around it. This will prevent rotting of the fabric. HOMELITE* i textronl DIVISION PORT CHESTER, NEW YORK, U.S.A. 10573 7 P.T.O. Driven Vacuum Collector No. Description Part No. Qty. No. Description Part No. 1 "V" BELT-drive LM-01650-48 1 47 STOP-belt LM-16059-62 2 COVER-belt drive LM-16056-59 1 48 SPACER LM-01561-49 3 SCREW-cap, 5/16-18 x 2 LM-09193-55 1 49 SCREW-cap, 3/8-16 x 3 LM-09166-07 4 SCREW-cap, 5/16-18 x 4 LM-09221-04 1 00 ARM-idler LM-16058-14 5 SCREW-cap, 7/16-14 x 1-1/4 LM-09234-71 1 51 PIVOT-idler arm LM-16058-15 6 SCREW-set, 5/16-18'x 1/2 sq. hd. cup.pt. LM-09287-21 52 PULLEY LM-01010-96 7 KEY-paratlel, flat, 3/16 x 3/16 x 1 LM-09058-50 1 53 SPRING-tens ion LM-16028-94 8 PULLEY LM-01642-02 1 54 SCREW-cap, 1/4-20 x 1 LM-09173-96 9 WASHER-flat, 7/16 LM-09184-30 1 55 SPACER LM-16104-16 10 SCREW-cap, 3/8-16 x 1-1/8 LM-09193-58 1 56 PULLEY-idler LM-01083-86 11 WASHER-flat, 13/32 x 7/8 LM-09249-40 7 57 SPACER-hood (R. H.) LM-01065-77 12 STOP-belt LM-16 06 0-14 3 58 SCREW-cap, 3/8-16 x 1 LM-09077-31 13 WASHER-lock, 3/8 LM-09169-65 14 59 BRACKET ASSEMBLY-idler support LM-16083-46 14 NUT-hex, 3/8-16 LM-09169-50 11 60 PULLEY LM-16028-81 15 WASHER-lock, 1/4 LM-09169-64 13 61 WASHER-flat, 1/4 LM-09182-64 16 NUT-hex, 1/4-20 LM-09166-22 13 62 CLIP-baffle LM-01081-86 17 NUT ASSEMBLY LM-01230-60 2 63 GUIDE ASSEMBLY-rod LM-16043-19 18 BOLT-carriage LM-07030-07 2 64 KEY-Woodruff, 3/16 x 3/4 LM-09051-23 19 ADAPT...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: