Always wear eye protection, gloves and a respirator when operating this unit. Part Number 80702 Rev. 4/02 Shindaiwa Inc. 11975 S.W. Herman Road Tualatin, Oregon 97062 Telephone: 503 692-3070 Fax: 503 692-6696 2002 Shindaiwa, Inc. Part Number 80702 Revision 4/02 Shindaiwa is a registered trademark of Shindaiwa, Inc. Specifications subject to change without notice. Printed in Brazil Introduction This manual contains information for the proper assembly, operation and care of your SP518 sprayer. Ca

Always wear clothing and safety equipment that will provide appropriate protection against the materials you are handling. Equipment may include, but not be limited to: ¦Long sleeve shirt ¦Impermeable apron or coverall ¦Impermeable gloves and boots ¦Wide-brim hat ¦Protective mask equipped with appropriate filters Do not eat, drink, or smoke while handling chemicals or while you are spraying. Always handle chemicals in a well ventilated area while wearing appropriate protective clothing and safet

Always wear eye and hearing protection when operating this unit. WARNING! Part Number 62719-94310 Rev. 11/06 Introduction General Safety Instructions Attention Statements The Shindaiwa 231-series of hand-held power tools has been designed and built to deliver superior performance and reliability without compromise to quality, comfort, safety or durability. Shindaiwa’s high-performance engines represent the leading edge of 2-cycle engine technology, delivering exceptionally high power with remark

Remove both screws from the handle. 2. While spreading the handle at the mounting hole, position the handle on the outer tube as shown. 3. Reinstall the two mounting screws in the handle, but do not tighten them at this time. NOTE: The handle is recessed to receive the hex nuts. 4. Locate the handle at the best position for operator comfort (usually about 10 inches ahead of the throttle assembly). 5. Secure the handle by tightening the mounting screw and the adjustment knob screw. Hex Nut Hex Nu

Figure 24 50-Hour Maintenance Lubricate the Flexible Shaft. Lack of lubrication will cause rapid wear to the flexible shaft and also to the shaft tube liner, resulting in increased vibration and greatly decreased service life. Remove and lubricate the flexible shaft as follows: Refer to Figure 27: 1. Loosen the gearcase clamp screw. 2. Remove the gearcase index screw. 3. Slide the gearcase and shield assembly from the shaft tube. 4. Pull the flexible shaft from the shaft tube assembly, and clean

Use of non-approved mixing oils can lead to excessive carbon deposits. Examples of 50:1 mixing quantities n 1 gallon of gasoline to 2.6 oz. mixing oil. n 5 liters of gasoline to 100 ml. mixing oil. Oil is a registered JASO FC classified oil and also meets or exceeds ISO-L- EGD performance requirements. Shindaiwa One is recommended for use in all Shindaiwa low emissions engines. Shindaiwa One also includes a fuel stabilizer. Filling the Fuel Tank WARNING! Minimize the Risk of Fire! n ALWAYS stop

It is highly recommended that this is done by a Shindaiwa-trained service technician. ¦ Replace the spark plug annually: Use only the type recommended in the ”Specifications” section or an equivalent resistor type spark plug of the correct heat range. Set spark plug electrode gap to 0.6 mm. IMPORTANT! The valve clearance should be adjusted. It is highly recommended that this is done by a Shindaiwa-trained service technician. Valve Adjustment 1. Remove cylinder cover, rocker arm cover, and spark

To minimize the risk of injury, read this manual and familiarize yourself with its contents. X7502825800 Introduction The Shindaiwa H4 series has been designed and built to deliver superior performance and reliability without compromise to quality, comfort, safety or durability. Shindaiwa engines represent the leading edge of high-performance engine technology, delivering exceptionally high power with remarkably low displacement and weight. As an owner/operator, you’ll soon discover for yourself

arrester! Operating with a missing or ............................................................................ and could also damage your hearing. 1. With a 3 mm hex wrench remove the 4 engine cover screws and the engine cover. 2. With a 4 mm hex wrench, remove the 3 muffler bolts and the muffler. 3. With a small flat bladed screwdriver remove the 2 screws holding the spark arrester screen and cover to the muffler. 4. Remove the screen and clean it with a stiff bristle brush. 5. Inspect the

NOTE: Using non-standard replacement parts could invalidate your Shindaiwa warranty. ..........U This unit must never be operated with a faulty or missing spark arrester or muffler. Make sure the muffler is well secured and in good condition. A worn or damaged muffler is a fire hazard and may also cause hearing loss. Spark Plug Keep the spark plug and wire connections tight and clean. Daily Maintenance Prior to each work day, perform the following: Y Remove all dirt and debris from the engine, c