Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
NOTE: Using non-standard replacement parts could invalidate your Shindaiwa warranty. ..........U This unit must never be operated with a faulty or missing spark arrester or muffler. Make sure the muffler is well secured and in good condition. A worn or damaged muffler is a fire hazard and may also cause hearing loss. Spark Plug Keep the spark plug and wire connections tight and clean. Daily Maintenance Prior to each work day, perform the following: Y Remove all dirt and debris from the engine, check the cooling fins and air cleaner for clogging, and clean as necessary. Y Clean any debris or dirt from the cutting attachment. Y Check the entire unit for leaking fuel or grease. Y Check for loose or missing screws or components. Make sure the cutter attachment is securely fastened. Y Make sure nuts, bolts, and screws (except carburetor idle speed adjusting screws) are tight. Y Carefully remove any accumulations of dirt or debris from the muffler and fuel tank. Check cooling air intake area at base of crankcase. Remove all debris. Dirt build-up in these areas can lead to engine overheating, fire, or premature wear. WARNING! Before performing any maintenance, repair, or cleaning work on the unit, make sure the engine and cutting attachment are completely stopped. Disconnect the spark plug wire before performing service or maintenance. Fasteners Make sure nuts, bolts, and screws (except carburetor adjusting screws) are tight. Air Filter The C4 engine that powers your Shindaiwa model is a hybrid 4-stroke engine. As a hybrid, the engine is lubricated by oil mixed with the gasoline and air from the carburetor that moves through and around the internal parts of the engine in a similar way that a 2-stroke engine is lubricated. Without the heavy duty 2-stage air filter equipped on all C4 engines, dust and dirt could also move through the engine, decreasing engine life, increasing valve wear and the need for more frequent valve adjustments. To keep your C4 engine strong and reliable, Shindaiwa recommends that you check and service the air filter as instructed in the 10-Hour Maintenance section that follows. WARNING! Non-standard accessories, cutting attachment, or replacement parts may not operate properly with your unit and may cause damage and lead to personal injury. Blades Keep blades sharp and check blade condition frequently. If a blade’s performance changes suddenly, stop the engine and check the blade for cracks or other damage. Replace a damaged blade IMMEDIATELY! WARNING! Y Never repair a damaged blade by welding, straightening, or by modifying its shape. An altered blade may break during operation, resulting in serious personal injury. Y Blades are not interchangeable between Shindaiwa edgers and unit/brushcutter models. Operating any unit with a blade or attachment not approved for that unit can be hazardous and may cause serious injury. ........................................................................................................................................ Cooling ...... Air intake Cooling ...... Maintenance (continued) 10-Hour Maintenance (more frequently in dusty conditions) 1. Remove the air cleaner cover by loosening the thumbscrews and lifting. 2. Remove and inspect the pre-filter. If the pre-filter is torn or otherwise damaged, replace it with a new one. 3. Clean the pre-filter with soap and water. Let dry before reinstalling. 4. Inspect the air filter element. If the element is damaged or distorted, replace it with a new one. 5. Tap filter gently on a hard surface to dislodge debris from element or use compressed air from the inside to blow debris out and away from the air filter element. 6. Install the air filter element, pre-filter and cover in the reverse order of removal. 10/15-Hour Maintenance Unscrew Fasteners Air Filter Element Pre-Filter IMPORTANT! Direct the air stream at the inside face of the filter only! CAUTION! Never operate the unit if the air cleaner assembly is damaged or missing! Remove and clean or replace the spark plug. Y Clean the spark plug. Adjust electrode gap according to the values listed in the ”Specifications” section. If the spark plug must be replaced, use only the type recommended in ”Specifications” or equivalent resistor type spark plug of the correct heat range. CAUTION! Before removing the spark plug, clean the area around the plug to prevent dirt and debris from getting into the engine’s internal parts. Clean the spark plug and check the gap at the electrode. 0.6–0.7 mm 50-hour Maintenance Remove and replace the fuel filter element Y Before reinstalling the new fuel filter element, inspect the condition of all the fuel system components (fuel pick-up line, fuel return line, tank vent line, tank vent, fuel cap and fuel tank). If damage, splitting or deterioration is noted, the unit should be removed from service until it can be inspected or repaired by a Shindaiwa-trained service technician. .................................... Hooked Wire ..............
Эта инструкция также подходит к моделям:Газонокосилки - 89307 (1.74 mb)