Оценок - 4, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
Failure to do so may result in spontaneous com bustion which could develop into a fi re. CAUTION:BEFORE PERFORMING ANY MAIN TE NANCE, SERVICE OR AD JUSTMENTS: • Depress clutch brake pedal fully and set parking brake. • Place gearshift/motion control lever in "NEU TRAL" position. • Place clutch control in "DIS EN GAGED" po si tion. • Turn ignition key to "OFF" position. • Make sure blades and all moving parts have completely stopped. • Disconnect spark plug wire(s) from spark plug(s) and place wire where it cannot come in contact with plug. CAUTION: Grass catcher components are subject to wear, damage and deterioration, which could expose moving parts or allow objects to be thrown. Frequently check components and replace with manufacturer's recommended parts, when necessary. 13 PREPARATION CAUTION: BEFORE PROCEEDING WITH PREPARATION OF TRACTOR: • Depress clutch/brake pedal fully and set parking brake. • Place gearshift/motion control lever in "NEUTRAL" position. • Place attachment clutch in "DISENGAGED" position. • Turn ignition key "OFF" and remove key. • Make sure the blade and all moving parts have completely stopped. • Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. NOTE ON SOME MODEL TRACTORS, MINOR MODIFICATIONS MAY BE NECESSARY TO MOUNT YOUR NEW GRASS CATCHER. NOT ALL MODEL TRACTORS WILL NEED THE FOLLOWING MODIFICATIONS. CHECK EACH STEP CARE FUL LY TO DETERMINE IF MODIFICATION IS REQUIRED. ONCE YOUR MODEL TRACTOR CONFORMS TO THIS SECTION PRO CEED TO ASSEMBLY. To Prepare your Grass Catcher you may need: (1) Drill Motor (1) 7/16" Drill Bit DRILL SUPPORT TUBE MOUNTING HOLES IN DRAWBAR (See Template) On some model tractors, two 7/16" holes must be drilled in left side of the drawbar for mounting the support tube. NOTE: To ease in drilling 7/16" holes, it may be necessary to drill smaller pilot holes at the locations indicated. 14 DRILL TWO7/16" HOLES AT LOCATIONSHOWN DRILL TWO 7/16" HOLES 1) CUT OUT TEMPLATE. 2) ALIGN BOTTOM AND LEFT EDGE OF TEMPLATE AND DRAWBAR. 3) TAPE IN POSITION. 4) MARK AND DRILL 7/16" HOLES NOTE: DRILL SMALLER PILOT HOLES PRIOR TO DRILLING 7/16" HOLES 5) PROCEED WITH STEP 1 OF ASSEMBLY INSTRUCTIONS DRILL TWO7/16" HOLES AT LOCATIONSHOWN DRILL TWO 7/16" HOLES 1) CUT OUT TEMPLATE. 2) ALIGN BOTTOM AND LEFT EDGE OF TEMPLATE AND DRAWBAR. 3) TAPE IN POSITION. 4) MARK AND DRILL 7/16" HOLES NOTE: DRILL SMALLER PILOT HOLES PRIOR TO DRILLING 7/16" HOLES 5) PROCEED WITH STEP 1 OF ASSEMBLY INSTRUCTIONS 15 NOTES 16 NOTES 17 18 WARNING Donotoperatemowerunlesscontainerisproperlyis nstalled.Containeris subjectto wearand detierioration.Check bagfrequently.Replacewhen cracked ordamaged.Useonlyarecommendedreplacement container. WARNING Donotoperatemowerunless container is properlyisnstalled.Containeris subjectto wearand detierioration.Checkbagfrequently.Replacewhen cracked ordamaged.Useonlyarecommendedreplacementcontainer. 2 3 4 20 2 35 20 37 2 34 33 20 25 20 9 12 13 14 18 5 8 9 9 10 11 24 32 47 47 30 26 25 28 27 27 26 36 25 20 9 12 16 15 15 16 14 40 40 40 2 2 39 29 29 6 7 WARNING Donotoperatemowerunlesscontainerisproperlyisnstalled.Containeris subjecttowearand detierioration.Checkbagfrequently.Replacewhen cracked ordamaged.Use onlyarecommendedreplacementcontainer. 31 31 31 25 33 20 38 2 43 44 45 42 41 20 46 27 20 REPAIR PARTS / PIECES DE RECHANGE GRASS CATCHER - - MODEL NUMBER CL46B / RAMASSE-HERBE - - NUMERO DE MODELE CL46B PRODUCT NUMBER 954 04 06-06 / NUMERO DE PRODUIT 954 04 06-06 REP AIR P AR TS / PI ECES D E REC HANG E G R A S S C A T C H E R - - M O D E L N U M B E R C L 46B / R A M A S S E -H E R B E - - N U M ER O D E M O D EL E C L 46B P R O D U C T N U M B E R 954 04 06-0 6 / N U M ER O D E P R O D U IT 95 4 04 06-0 6 19 KEY PART DESCRIPTION KEY PART DESCRIPTION NO. NO. NO. NO. 2 532069180 Nut, Crown lock #10-24 Ecrou auto-serrant #10-24 27 874760512 Bolt, Hex 5/16-18 x 3/4 Boulon H 5/16-18 x 3/4 3 532127533 Screen, Cover Ecran de couvercle 28 532170053 Bracket, Mounting Support de montage 4 532139850 Cover Assembly Couvercle 29 532170165 Shoulder Bolt,Self Tapping Boulon autotaraudeuse (Includes 3, 37, 38, 39) (Y compris 3, 37,38,39) 30 532131137 Pin, Support Post Goupille du poteau de soutien 5 532126840 Chute, Upper Glissiere superieure 31 532174083 Plug, Tubing End Capuchon d’extremite de tuyau 6 818021008 Screw, Special #10-14x1/2 Vis speciale #10-14x1/2 32 532134639 Bagger, Frame Cadre de ramasse-herbe 7 532140572 Dump Bag Indicator Indicateur de sac plein 33 532128600 Pin, Hinge Goupille de charniere 8 532087175 Screw, #10-24 x 1-1/8 Vis #10-24 x 1-1/8 34 532127534 Gasket, Cover Garniture de couvercle 9 819061216 Washer 3/16x3/4x16 Ga. Rondelle 3/16x3/4x16 Ja. 35 532183286 Container, Top Bac a gazon superieur 10 532007206 Spacer, Split Entretoise fendue 36 532129586 Container, Bottom Bac a gazon inferieur 11 532060867 Nut, Acorn #10-24 Ecrou borgne #10-24 37 532134637 Seal, Cover Sceau de couvercle 12 810071000 Washer, lock Rondell...
Эта инструкция также подходит к моделям:Газонокосилки - 954 04 06-06 (868.82 kb)