Оценок - 2, средний балл: 5
(
)
)
|
Фрагмент инструкции
Insert the two rear ends into the special slots in the casing and fix the guard by inserting the washers and M5 nuts on M5 x 20 screws and fix to the casing. (),. 1. Fasten the seat (1) to the support plate (22) through the 4 M8 x 18 screws. Assemble with 4 washers O 9 x 24 and 4 grower. 2. Before tightening the screws, adjust the position of the seat on the holes of the plate to suit the user's needs. ((),. Fasten the bin to the rear part of the ride-on-mower with the 2 H.H. 6x16, 2 screws, the 2 Z- shaped plates and 2 M5 nuts. . The openings at the steering wheel and at the steering column must be in exact alignment. Check at regular intervals that the nuts are tightly screwed down. Before the cutting height is adjusted, the engine must be switched off and the blades must have come to complete standstill. $(),. 1. Push the adjustment lever (12) outwards in order to release it from its seat. 2. Push the lever into the required notch for the cutting height. 3. Release the lever slowly till it sticks in the notch. The cutting height is now set. 15 ENGLAND "(),. Empty the grass collection bag in time before it overflows. The red light situated under the steering wheel shows that the bin is full. Don’t go on filling the grass collection bin when the red light situated under the steering wheel is on. (,,. The modern gardening technology has designed and developed labour-saving devices (mower with grass collection bag). For a good, healthy green lawn, it is essential to mow and aerate it regularly. Fertilising is also essential. Always make sure the blades are sharp and in perfect conditions to avoid grass fraying and yellowing of the lawn. . You will achieve a clean cut with regular and straight windrows. The mowing tracks should always overlap a few centimetres to avoid any uncut strips in between. ()-. Switch off the engine. 1. Hold the rod and swivel the bag. Shake the bag twice until it is completely empty. 2. Let the grass collection bag return slowly to its original position. 3. Switch on the engine. Lawn cutting frequency depends on the rate of growth. In the main growing season (May-June) often (twice a week) or at least once a week.The cutting height should be between 4-6 cm. and the growth before the next cut should not be more than 45 cm. During hot and dry periods, the lawn should be cut 1,5 cm. higher than normal, to avoid ground and root drying out. If the grass is somewhat higher than normal, you should not make the mistake of cutting it immediately; you can damage the lawn. Do no cut to more than half the necessary height. Before mowing, remove all foreign objects from the lawn which may be thrown by the machine. While mowing, stay alert for any foreign objects which may have been missed. ()-. Never place your hands or feet underneath the deck or into the rear discharge chute while the engine is running. . ",,"(. The ride-on lawnmower may be put into operation for the first time only by trained (. persons only who have read and fully understand the operating instructions. Don’t put the ride-on lawnmower into operation before you have completely finished its Use the following on your ride-on lawnmower: assembly. Before putting the ride-on lawnmower into operation for the first time, don’t forget to fill it with petrol and oil. Connect the red cables to the positive terminal and the black cables to the negative terminal (the battery is placed in battery holder under the Petrol lead free (min. octane rating 77) motor safety housing on the right of the seat). engine oil SAE 30 ("SE", "SF" O "SG") . Start up the engine only after filling the tanks with sufficient petrol and oil. Carefully follow the instructions in the enclosed engine manufacturer’s operating and maintenance manual. (()-. Danger of explosion! Fill the tank only only in an open area! Never refuel while the engine is running or is very hot! Do not smoke! The petrol tank is placed in the engine block below the seat. 1. Lift the seat 2. Unscrew the tank cap (23) and fill up with lead-free petrol. 3. Screw the tank cap back. """,. 1. Lift the seat onto the ground. Use only oil of type SAE 30 (“SE”, “SF” or “SG”). Ensure that no oil is spilt 2. Unscrew the oil filler cap (24) 3. Fill up the oil until the “MAX.” mark on the dip stick is reached 4. Replace the oil filler cap. The oil filler cap is placed in the engine block, below the seat. . The exhaust fumes contain carbon monoxide, an odourless and deadly gas. Never start the engine in closed or badly ventilated rooms. ()). Look for a flat piece of ground with short grass for starting the engine. Operate the electric start only when sitting on the tractor with the blade clutch (8) in stop position and with brake engaged. 1. Set the clutch blade (8) to STOP position 2. Set the throttle lever (6) to START position 3. Press the brake pedal (9 - Fig.I). ()). 4. Insert the ignition key in the ignition block (5) 5. Turn the key to the right and release it, after starting in “RUN” posit...
Эта инструкция также подходит к моделям:Газонокосилки - Choppy 95387831900 (2.08 mb)