Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Tighten oil plug securely each time you check the oil level. bolt Hardened :::,, \ ...../ washer Trailing edge Crankshaft 12 TO CHANGE ENGINE OIL . Install cartridge, then replace cover NOTE: Before tipping lawn mower to drain oil, empty fuel tank by running engine until fuel tank is empty. 1. Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. 2. Remove engine oil cap; lay aside on a clean surface. 3. Tip lawn mower on its side as shown and drain oil into a suitable container. Rock lawn mower back and forth to remove any oil trapped inside of engine. 4. Wipe off any spilled oil from lawn mower or side of engine. 5. Slowly pour oil down the oil fill spout, stopping every few ounces to check the oi! level with the dipstick. 6. Stop adding oil when you reach the FULL mark on the dipstick. Wait a minute to allow oil to settle. 7. Continue adding small amounts of oil, rechecking the dipstick until oil level settles at FULL. DO NOT overfill, or engine will smoke heavily from the muffler on startup. 8. Always be sure to retighten oil dipstick before starting engine. 9. Reconnect spark plug wire to plug. AIR FILTER Your engine will not run properly and may be damaged by using a dirty air filter. Replace the air filter cartridge every 100 hours of operation or every season, which ever occurs first. Service air cleaner more often under dusty conditions. TO CLEAN AIR FILTER 1. Loosen screw and tilt cover to remove. 2. Carefully remove cartridge. 3. Clean by gently tapping on a flat surface. If very dirty, replace cartridge. _I,CAUTION: Petroleum solvents, such as kerosene, are not to be used to clean cartridge. They may cause deterioration of the cartridge. Do not oil cartridge. Do not use making sure the tabs are aligned with the slots in the back plate. Fasten screw securely. Back plate Cartridge Slot Cover Cover tab MUFFLER Inspect and replace corroded muffler as it could create a fire hazard and/or damage. SPARK PLUG Replace spark plug at the beginning of each mowing season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in the "PRODUCT SPECIFICATIONS" section of this manual. CLEANING IMPORTANT: For best performance, keep mower housing free of built-grass and trash. Clean the underside of your mower after each use. ,_I,CAUTION: Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. • Clean the underside of your lawn mower by scraping to remove build-up of grass and trash. • Clean engine often to keep trash from accumulating. A clogged engine runs hotter and shortens engine life. • Keep finished surfaces and wheels free of al! gasoline, oil, etc. • We do not recommend using a garden hose to clean lawn mower unless the electrical system, muffler, air filter and carburetor are covered to keep water out. Water in engine can result in shortened engine life. pressurized air to clean or dry cartridge. 13 ,_ WARNING: To avoid serious injury, before performing any service and adjustments: 1. Release control bar and stop engine. 2. Make sure the blade and al! moving parts have completely stopped. 3. Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. LAWN MOWER TO ADJUST CUTTING HEIGHT See "TO ADJUST CUTTING HEIGHT" in the Operation section of this manual. REAR DEFLECTOR The rear deflector, attached between the rear wheels of your mower, is provided to minimize the possibility that objects will be thrown out of the rear of the mower into the operator mowing position. If the deflector becomes damaged, it should be replaced. TO ADJUST HANDLE The handle can be mounted in a high or low position. The mounting holes in the bottom of lower handle are off center for raising or lowering the handle. 1. Remove upper handle and all wire tie(s) securing cable(s) to lower handle. 2. Remove hairpin cotters from lower handle bracket mounting pin. 3. Squeeze lower handle in to remove it from mounting pins. 4. Turn lower handle over to raise or lower handle. 5. Squeeze lower handle in and position holes onto mounting pins on handle bracket. 6. Reassemble upper handle and all parts removed from lower handle. SQUEEZE TO ADJUST Lower Mounting pin Handle Hairpin cotter Mowing r-'q Mowing position iI iI iI j'l Hairpin Handle Mounting bracket pin LOW POSITION HIGH POSITION \ Lower % handle.___ ROTATE __ ENGINE ENGINE SPEED Your engine speed has been factory set. Do not attempt to increase engine speed or it may result in personal injury. If you believe that engine is running too fast or too slow, take your mower to a Sears or other qualified service center for repair and adjustment. CARBURETOR Your carburetor is not adjustable. If your engine does not operate properly due to suspected carburetor problems, take your lawn mower to a Sears or other qualified service center for repair and/or adjustment. IMPORTANT: Never tamper with the engine governor, ...