Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
• Lowering the wheel will decrease the cutting depth. 3. Tighten the depth adjustment knob securely. MAINTENANCE SCHEDULE _l_ WARNING: Always stop unit and disconnect spark plug wire (or discon nect powerhead from power source) CARE AND MAINTENANCE TASK Check for loose fasteners and parts Check for damaged or worn parts Inspect and clean unit and decals Check or replace blade _ENERAL RECOMMENDATIONS The warranty on this attachment does not cover items that have been subjected to operator abuse or negligence, To receive full value from the warranty, the operator must maintain the edger attachment as instructed in this manual, CHECK FOR DAMAGED OR WORN PARTS Contact Sears Service Center for replacement of damaged or worn parts. * Blade Shield -Discontinue use of edger if blade shield is damaged. CHECK FOR LOOSE FASTENERS AND PARTS * Blade nut * Fasteners INSPECT AND CLEAN UNIT AND DECALS * After each use, inspect complete unit for loose or damaged parts. Clean the unit and decals using a damp cloth with a mild detergent. * Wipe off unit with a clean dry cloth. 9 before performing maintenance. WHEN TO PERFORM Before each use Before each use After each use Every 5 hours of operation BLADE MAINTENANCE _WARNING: The blade will con tinue to spin after the engine stops or after the throttle trigger has been released. To avoid serious injury, make sure the blade has stopped coasting and disconnect the spark plug (or disconnect powerhead from power source) before performing work on the blade. _I_WARNING: Always replace a blade that is bent, warped, cracked, broken, or damaged in any other way. Never attempt to straighten and reuse a damaged blade. Use only specified replacement blade. Wear protective gloves when handling or performing maintenance on the blade to help avoid injury. • The blade is reversible. When the cutting edge on one side becomes worn, turn the blade over (see BLADE REPLACEMENT in the SERVICE AND ADJUSTMENTS section). • Check blade for flatness periodically. Lay the blade on a flat surface to inspect for flatness. Throw away a blade that is not flat. BLADE REPLACEMENT _WARNING: The blade will con tinue to spin after the engine steps or after the throttle trigger has been released. To avoid serious injury, make sure the blade has stopped coasting and disconnect the spark plug (or disconnect powerhead from power source) before performing work on the blade. I_ WARNING: Wear protective gloves when handling or performing maintenance on the blade to avoid injury. The blade is sharp and can cut you even when it is not moving. 1. To remove the blade, align hole in the dust cup with the hole in the side of the gearbox by rotating the blade. 2. Insert a small screwdriver into aligned holes. This will keep the shaft from turning while loosening the blade nut. 3. While holding the screwdriver in position, remove blade nut by turning clockwise. 4. Remove both washers, and the blade from the blade shaft. Blade shield Blade Washers Blade Shaft 5. install new blade onto blade shaft. 6. Reinstall both washers and blade nut (counterclockwise). 7. Tighten blade nut firmly with a wrench while holding screwdriver in position. 8. Remove the screwdriver. 9. Turn blade by hand. if the blade binds against the shield, or appears to be uneven, the blade is not centered, and you must reinstall. 4_WARNING: Perform the following steps after each use: * Allow attachment and gearbox to cool before storing or transporting. * Store attachment with blade shield in place. Position attachment so that any sharp object cannot accidentally cause injury. * Store the attachment in a dry, well ventilated area out of the reach of children. SEASONAL STORAGE Prepare attachment for storage at end of season or if it will not be used for 30 days or more. If your edger attachment is to be stored for a period of time: • Clean the entire attachment. • inspect the blade shield area and clean any dirt, grass, leaves, or debris that has collected, inspect the blade and blade shield; replace a blade that is bent, warped, cracked, broken or damaged in any other way. • Lightly oil external metal surfaces. • Apply a coating of oil to the entire surface of the blade; wrap it in heavy paper or cloth. • Check entire attachment for loose screws or nuts. Replace any damaged, worn or broken parts. • At the beginning of the next season, use only fresh fuel having the proper gasoline to oil ratio. 10 Declaraci6n de Garantia 12 Mantenimiento 20 Identificaci6n de Simbolos 12 Servicio y Ajustes 21 Reglas de Seguridad 12 Almacenaje 22 Montaje 17 Lista de Piezas 11 Uso 18 Repuesto y Encargos Contratapa GARANTIA COMPLETA DE UN ANO PARA LA CORTADORA DE BORDES ACCESORIO CRAFTSMAN ® Durante un aSo, a partir de la fecha de compra, siempre que se haga el mantenimiento, la lubricaci6n y los ajustes a esta Cortadora de Bordes Accesorio Crafts man segt]n las instrucciones en el manual de instrucciones, Sears reparar_ cualquier defecto de materiales o de mano de obra gratuitamen...