Оценок - , средний балл:
(
)
)
Производитель: Cub Cadet
Размер: 1.47 mb
Название файла:
Язык инструкции:
Документ загружается, подождите пожалуйста
 |
Документ загружается, подождите пожалуйста
Фрагмент инструкции
Extensive vibration of the mower during operation is an indication of damage. The unit should be promptly inspected and repaired. ADJUSTMENTS A WARNING: Do not at any time make any adjustment to lawn mower without first stopping engine and disconnecting spark plug wire. CUTTING HEIGHT ADJUSTMENT The height adjustment handles for the wheels are located on the left side of the deck. The handles may be placed in one of nine cutting height positions. See figure 5. For rough or uneven lawns, move the height adjustment handles to positions which will give a higher cutting height. Both front and rear handles must be placed in the same relative position. HANDLE HEIGHT ADJUSTMENT Your mower is shipped with the handle in the higher height position. To lower the handle height, proceed as follows. 1. Remove the starter rope from the rope guide. 2. Remove the upper handle by removing the hand knobs and carriage bolts. Lay the upper handle out of the way, being careful not to bend or kink the cables. 3. Remove the hairpin clips from the weld pins on the handle brackets. Press outward on the legs of the lower handle for self-propelled models. For push models, press inward on the legs of the lower handle. Remove lower handle from the mower. 4. Turn the lower handle around so the notch on the bottom of the lower handle is facing forward as shown in figure 6. Reassemble, placing the bottom holes in the handle over the weld pins in the handle mounting bracket. 5. Reassemble the upper handle. 6. Place the hairpin clips in the inner holes in the weld pins and attach the starter rope as instructed in the Assembly Instructions. DRIVE CLUTCH CONTROL ADJUSTMENT (Self-Propelled Models Only) Use the adjustment wheel located in the clutch control housing to tighten the drive belt if mower does not self-propel with the drive clutch control engaged, or if drive belt is slipping (unit hesitates while engine maintains the same speed). See figure 7. In addition, the adjustment wheel may also be used to determine the position in which the drive clutch control is engaged. If it is more comfortable to have the drive engaged with the lever further away from the handle, tighten the drive belt. Make certain to retest the unit for neutral as instructed in the Operation Section. Move the adjustment wheel in the opposite direction to loosen the drive belt if necessary. 6 THROTTLE CONTROL ADJUSTMENT If the throttle control requires adjustment or if it has been replaced, adjust the throttle control as follows. 1. Remove the screw shown in figure 8. Remove the cable clamp from the cable. 2. Push the throttle control lever on the handle all the way forward as far as it will go, then back it off one “click”. Make certain the throttle control lever remains in this position. 3. Push the control lever on the engine as far toward the rear of the engine as it will go. Secure the cable in this position with the cable clamp and SIX SPEED SHIFT CABLE ADJUSTMENT (Self-Propelled Models Only) Periodic adjustment of the six speed shift cable may be required due to normal stretch and wear on the cable. Adjustment is needed if all six speeds cannot be obtained. The adjustable cable bracket is located on the left side of the mower, beside the engine. To adjust, loosen the hex nut which secures the adjustable cable bracket. See figure 9. Place the shift lever in the sixth speed position. Make certain the belt is not pinched between the pulley halves. Pull backward on the adjustable cable bracket (toward the rear of the mower). Retighten the hex nut. Test the speeds on the mower (engine must be running). Cable Bracket FIGURE 9. LUBRICATION A WARNING: Always stop engine and disconnect spark plug wire before cleaning, lubricating or doing any kind of work on lawn mower. Blade Control—Lubricate the pivot points on the blade control handle and the brake cable at least once a season with light oil. See figure 10. The blade control must operate freely in both directions. FIGURE 10. Wheels—Lubricate the wheel bearings at least once a season with light oil. Also, if the wheels are removed for any reason, lubricate the surface of the axle bolt and the inner surface of the wheel with light oil. A 4 oz. plastic bottle of light oil lubricant is available. Order part number 737-0170. Engine oil may also be used. Engine—Follow engine manual for lubrication instructions. Transmission (Self-Propelled Models Only)—The transmission is pre-lubricated and sealed at the factory. It does not require checking. If disassembled for any reason, fill with 2 ounces of Alvania grease, part number 737-0168. MAINTENANCE A WARNING: Be sure to disconnect and ground the spark plug wire before performing any repairs or maintenance. NOTE: When tipping the unit, empty the fuel tank and keep engine spark plug or air cleaner side up. TROUBLE SHOOTING Refer to page 10 of this manual for trouble shooting information. CUTTING BLADE When removing the cutting blade for s...
Эта инструкция также подходит к моделям:Газонокосилки - 108C (1.47 mb)