Оценок - 5, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
Rewind Wire Onto Spool, Fasten End Of Wire To Spool Cut Off End Of Wire Loosen Thumbscrew, Disconnect Gun Trigger Plug, And Pull Gun From Unit Ref. 804 686-A Thumbscrew OM-230 261 Page 12 3-3. Connecting Spool Gun To Handler 210 804 695-A 1 Drive Assembly 2 Spool Gun 3 Gun Securing Thumbscrew 4 Gun End Loosen thumbscrew. Insert end through opening until it bottoms against drive assembly. Tighten thumbscrew. Spool gun must be inserted completely to prevent leakage of shielding gas. 5 Gun Trigger Plug Insert plug into receptacle, and tighten threaded collar. 6 Spool Gun/MIG Gun Switch Place switch in Spool Gun position. 7 Polarity Changeover Terminal Block To make proper polarity connection, see welding power source Owner’s Manual. Close door. Incorrect Correct Be sure that gun end is tight against drive assembly. 3 Gun Fully Seated 3 Gun Not Seated Exposed O-rings will cause shielding gas leakage. 5 1 3 4 2 Spool Gun 6 MIG Gun 7 CC CC OM-230 261 Page 13 3-4. Installing Wire Spool And Threading Welding Wire 804 697-A Tools Needed: 1 Thumb Screw 2 Spool Cover Remove thumb screw and spool cover. 3 Hub Tension Nut 4 Wire Spool Install spool so wire feeds from top. Turn hub tension nut just so a slight drag is felt on the wire spool. 5 Push Roll/Lower Drive Roll 6 Drive Roll Pressure Adjustment Opening 7 Drive Roll Release Lever (Red) 8 Wire Inlet Guide 9 Contact Tip 10 Nozzle Remove nozzle and contact tip. Push and hold red lever. Thread wire through inlet guide, past push roll/drive roll, and out end of gun 2 inches (50 mm). Release red lever. Turn On welding power source power. Install contact tip and nozzle. Reinstall spool cover and thumb screw. Wood Press gun trigger to feed wire to check drive roll Cut off wire. pressure. Turn screw enough to prevent slipping. Rotating screw clockwise decreases drive roll pressure and counterclockwise increases pressure. 4 1 5 6 7 8 10 9 3 2 OM-230 261 Page 14 SECTION 4 . OPERATION 4-1. Controls sb5.1* 6/92 . S-0621-C / Ref. 804 695-A / 804 696-A Spool Gun/MIG Gun switch on Handler 210 must be in Spool Gun position for spool gun to operate. 1 Shielding Gas Cylinder For shielding gas connections, see welding power source Owner’s Manual. 2 Valve Open valve on cylinder just before welding. Close valve on cylinder when finished welding. 3 Spool Gun/MIG Gun Switch Switch must be set in Spool Gun position for spool gun to operate. 4 Trigger Press trigger to energize welding power source contactor, start shielding gas flow, and begin wire feed. 5 Wire Feed Speed Control Wire feed speed is controlled by welding power source Wire Speed control (see welding power source Owner’s Manual or door chart for appropriate setting). 6 Voltage Control Arc voltage is controlled by welding power source Voltage control (see welding power source Owner’s Manual or door chart for appropriate setting). To purge shielding gas line, set gun selection switch (item 3) to the MIG Gun position.Press spool gun trigger to energize gas valve. Shielding gas will flow, but spool gun will not feed wire. Hold trigger in for several seconds to purge gas line. Return gun selection switch to the Spool Gun position before welding. 1 2 Spool Gun 3 MIG Gun 4 6 5 CCC CCC CCC OM-230 261 Page 15 SECTION 5 . MAINTENANCE & TROUBLESHOOTING 5-1. Routine Maintenance ! Disconnect power before maintaining. Maintain more often during severe conditions. = Check = Change = Clean = Replace * To be done by Factory Authorized Service Agent Reference Every 3 Months Unreadable Labels Weld Terminals Damaged Gas Hose Weld Cables Cords Gun Cables Every 6 Months OR Drive Rolls Inside Unit 5-2. Changing Drive Rolls 804 698-A Tools Needed: Turn Off power at welding power source first. 1 Drive Roll Cover Remove cover. Changing Push Roll: To remove push roll: 2 Push Roll Screw 3 Washer 4 Push Roll Remove screw and washer, and lift out drive roll. To install drive roll: Slide drive roll onto shaft and secure with washer and screw. Changing Lower Drive Roll: To remove drive roll: 5 Lower Drive Roll Screw 6 Washer 7 Lower Drive Roll 8 Drive Roll Key 9 Drive Roll Shaft Remove screw and washer, and lift out drive roll. Note: drive roll key will come out with drive roll. To install drive roll: Place drive roll key in slot in drive roll shaft. Line slot in drive roll up with drive roll key, and slide drive roll onto shaft. Secure drive roll with washer and screw. Reinstall gun case, if applicable. Reinstall drive roll cover. It may be necessary to remove drive roll side of gun case to change lower drive roll. 5 6 7 8 9 1 2 3 4 OM-230 261 Page 16 5-3. Changing Liner Ref. 804 687-A Tools Needed: Turn Off power at welding power source first. 1 Nozzle 2 Contact Tip 3 Liner Remove and replace liner. Reinstall parts as shown. 1 2 3 5-4. Troubleshooting Trouble Remedy Gun tube assembly loose. Tighten nut at base of gun tube assembly. No weld output; gun/feeder does not work. Place Power switch on welding power source in the On position (see...
Эта инструкция также подходит к моделям:Сварочные аппараты - DP 3035-20 (627.8 kb)