Оценок - 3, средний балл: 3 ( )

Производитель: Ariens Размер: 826.18 kb Название файла: Язык инструкции:

Kickout Ring 2. Sleeve Bushing 3. Clevis Pin 4. Mount Arm 5. Axle Tab 6. Flange Bushing 7. Wheel Yoke 8. Lube Fitting 1 2 3 4 2 5 6 7 8 PM0071 Figure 24 1. Kickout Ring 2. Sleeve Bushing 3. Clevis Pin 4. Mount Arm 5. Axle Tab 6. Flange Bushing 7. Wheel Yoke 8. Lube Fitting 1 2 3 4 2 5 6 7 8 PM0071 6 SECTION 7 - HANDLEBARS & CONTROLS SECTION 7 - HANDLEBARS & CONTROLS HANDLEBARS AND BAILS To remove handlebars: Remove cable retainers and disconnect cable from bail. Remove push nuts and washers securing bails to handlebars. Remove bails from handlebars. Remove carriage bolts and washers or knob and washers securing braces to handlebars. Remove braces. Remove carriage bolt, nut and washer securing handlebar to handlebar bracket. Remove handlebars and inspect parts for wear and or damage. Replace as necessary and assemble in reverse order. Check all parts for wear and replace as needed. 7.2 SPEED CONTROL BELL CRANK To adjust models with spring, fully compress compression spring with lock nut and then back lock nut off one turn. To adjust units without spring: 1. Remove cover and completely compress helical spring lockwashers with locknut, then back off 1/4 turn. 2. If rod is still too loose, tighten nut in small increments until the rod holds. Figure 25 Friction Wheel Handlebars and Controls 1. Engine Bail 2. Handlebar 3. Traction Bail 4. Cable Anchor 5. Cable Anchor Switch 6. Throttle Cable 7. Engine Control Cable 8. Traction Cable 9. Speed Control Brace 10.Rivet 11.Speed Control Bracket 12.Support Pad 13.Speed Control Rod 14.Handlebar Adjuster Link PM0024 1 2 3 4 5 6 7 8 9 10 11 12 13 14 14 7 - 37 1 2 3 4 5 6 7 Figure 26 Gear Drive Handlebars and Controls 1. Traction Bail 2. Handlebar 3. Engine Bail Weldment 4. Engine Control Cable 5. Throttle Cable 6. Handlebar Adjuster 7. Speed Control Bracket PM0320 1 2 3 4 5 6 7 Figure 26 Gear Drive Handlebars and Controls 1. Traction Bail 2. Handlebar 3. Engine Bail Weldment 4. Engine Control Cable 5. Throttle Cable 6. Handlebar Adjuster 7. Speed Control Bracket PM0320 8 SECTION 8 - ELECTRICAL SECTION 8 - ELECTRICAL BATTERY (ELECTRIC START MODELS) IMPORTANT: Use battery charger supplied only. DO NOT attempt to "jump start" mower. To charge with battery charger, connect charger plug to mating plug on battery (not engine) and plug charger into 110 volt Alternating Current (A.C.) outlet. Charge for 24 to 48 hours (battery may be charged for up to 72 hours with no harmful effects). An engine run time of at least 8 hours is required to charge a fully discharged battery. To Remove Battery from Unit 1. Remove wing nuts from battery U-bolt. 2. Disconnect battery from wiring. 8.2 WIRING DIAGRAM S B A M R REDBLACK BATTERY 1 2 3 4 A B KEY SWITCH RED BLACK REDREDRED RED YELLOW WHITE BLACK GREEN ENGINE 1 2 3 4 PM0090 8.3 CONTINUITY DIAGRAM The diagram below shows the various states of connection for electrical components. The solid lines on switches show continuity. NOTE: All switches are viewed from the rear. Key Switch (01155800) S B A MR S B A MR RUN OFF S B A MR START PM0100 8 - 39 SECTION 9 - FRICTION DRIVE SYSTEM & AXLE SECTION 9 - FRICTION DRIVE SYSTEM & AXLE INTRODUCTION WARNING: Remove wire from spark plug before attempting any repair or adjustment procedures. WARNING: Gasoline is highly flammable and its vapors are explosive. Handle with care. CAUTION: DO NOT touch engine or parts which are hot from operation. Allow such parts to cool before servicing unit. NOTE: Rear wheels must be removed to perform repairs in this section. Block up rear of mower to raise rear wheels off work surface. Remove snap ring securing wheel to axle and remove washer and wheel. 9.2 GEAR REMOVAL Remove snap ring securing gear cover over idler shaft, remove taptites securing cover to drive mount, and remove gear cover. Slide differential assembly off axle and remove idler gear from idler shaft. Drive out roll pin securing pinion gear on hex shaft and remove pinion gear. Inspect parts for wear and or damage, replace as necessary. Assemble in reverse order and grease spline area. 9.3 AXLE REMOVAL Remove snap ring next to axle spline on left side of axle and remove axle bearing. Remove cotter pin securing left side of rear protective guard to bracket and move guard out of the way. With snap ring pliers, spread snap ring apart on right side of axle. Pull right wheel and axle from mower until left end of axle clears drive mount. Inspect parts for wear and or damage, replace as necessary and assemble in reverse order being sure to grease spline area. 1 2 3 4 5 6 7 8 1. Differential 5. Pivot Channel 2. Idler Gear 6. Drive Disk 3. Pinion Gear 7. Friction Wheel 4. Drive Carrier 8. Shift Link Figure 27 9.4 DRIVE MOUNT REMOVAL Remove axle and gears. Refer to Axle Removal and Gear Removal Sections. Remove extension spring from drive actuator. Loosen nuts securing drive cable to drive actuator. Remove drive cable spring from bracket on mower pan and remove drive cable from drive actuator. Remove cotter pin and was...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: