Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
This kit should be installed when using the Triple Bagger Grass Collection System. Kit Contents: Ref Part No. Qty. Description 1 22467 2 Oil Cooler 2 1846152 1 Mount Bracket-Left 3 1846153 1 Mount Bracket-Right 4 1846154 1 Oil Cooler Mount 5 22106 2 3/8” Hose Fitting 6 21164 4 Hose Clamp 7 25299 8 Bolt, 1/4-20 x 3/4” Torx Head 8 25095 8 Nut, 1/4-20 Nylon Lock 9 50860-19 1 3/8” Hose, 19” (not shown) 10 50860-25 1 3/8” Hose, 25” (not shown) 11 50860-48 2 3/8” Hose, 48” (not shown) 12 50862-18 1 3/4” Wire Loom, 18” (not shown) 12 50862-24 1 3/4” Wire Loom, 24” (not shown) 13 21029 3 Long Tie Wrap (not shown) 14 21030 1 Short Tie Wrap (not shown) WARNING Before beginning any service work turn off the PTO, set the parking brake, turn off the ignition, and disconnect the spark plug wire(s). REMOVAL & INSTALLATION 1. Park machine on a flat, level surface and engage the parking brake. 2. Remove and discard the fuel tank tie bar and the left and right mounting brackets. SAVE the mounting hardware. NOTE:Some oil loss will occur when disconnecting the 3. Remove the split collars from the control cross shaft hydraulic hoses. Remove and reconnect as quickly as and carefully lift the shaft assembly from the saddles. possible and prepare to contain the lost oil. Set the shaft on the ledge of the rear seat support to allow for increased access room. 5. Remove the right return hose and loosen the jam nut on the fitting on the pump. Rotate the fitting towards 4. Subassemble the 19” and 25” hose lengths with one the rear of the machine and point it slightly upwards of the barbed fittings on each hose and the appropri (see Figure 2). Tighten the jam nut. ate length of wire loom. Be sure the barbs are fully inserted into the hose end. Applying a few drops of 6. Install the 19” hose assembly to the fitting on the oil on the barbs will make the assemble easier. pump and tighten. Leave the free end of the hose higher than the reservoir to prevent to hydraulic system from draining. 1846261 © Copyright 2000 Ferris Industries. All Rights Reserved. 1 Rev. 9/2000 TP 200-7030-00-SL-D Figure 1. Kit Contents 1 4 32 8 7 6 5 Figure 2. Fitting Orientation Installation Instructions 1846197 7. Block the front wheels and jack up the rear of the machine and set on jack stands or wooden blocks. Remove the left drive tire. This will allow for easier access to the left hand pump. 8. Remove the left return hose and loosen the jam nut on the fitting on the pump. Rotate the fitting towards the rear of the machine and point it slightly upwards (see Figure 2). Tighten the jam nut. 9. Install the 25” hose assembly to the fitting on the pump and tighten. Leave the free end of the hose higher than the reservoir to prevent to hydraulic system from draining. Route the hose behind the high- pressure hoses (see Figure 3). 10. Remove both return hoses from the top of the reservoir and save the hose clamps. 11. Reinstall the control cross shaft into the saddles. Make sure the new hoses do not contact ...
Эта инструкция также подходит к моделям:Газонокосилки - Derby 1846197 (82.56 kb)
Газонокосилки - Derby ZT2354 (82.56 kb)