Оценок - 5, средний балл: 4
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
You may not be able to shoot in temperatures below 5°C (41°F). – The battery remaining indicator may not display the correct information. 1 , Insert Nickel-Metal Hydride batteries into the battery charger (supplied) with the correct polarity +/.. • You cannot charge alkaline batteries using the battery charger. • Be sure to charge the Nickel-Metal Hydride batteries supplied with your camera before using them. • Connect the battery charger to an easily accessible wall outlet (wall socket) close by. • Even if the CHARGE lamp is not lit, the set is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet (wall socket). If some trouble occurs while using the battery charger, immediately shut off the power by disconnecting the plug from the wall outlet (wall socket). 2 CHARGE lamp Power cord (mains lead) to a wall outlet (wall socket) , Connect the battery charger to a wall outlet (wall socket) using the power cord (mains lead). Charging starts, and the CHARGE lamp lights. When the CHARGE lamp goes out, charging is finished. For details on the battery charger, see page page 111. To remove the batteries Press the - end of the battery down in order to raise the + end, then remove the battery. • When charging is finished, disconnect the power cord (mains lead) from the wall outlet (wall socket), and remove the Nickel-Metal Hydride batteries from the battery charger. Charging time Nickel-Metal Hydride Charging time battery Approx. 6 hours NH-AA-DA . 2 (supplied) This represents the time required to charge fully depleted Nickel-Metal Hydride batteries using the supplied battery charger in an environment where the ambient temperature is 25°C (77°F). • Charging is complete in approximately six hours. The CHARGE lamp may remain lit longer than six hours, but this is not a malfunction. • If you use the BC-CSQ2 battery charger supplied with the STAMINA “Super Quick charge” kit (not supplied), the batteries will charge faster. Charging time When charging two Nickel-Metal Hydride batteries: Approximately 2 hours 30 minutes When charging four Nickel-Metal Hydride batteries: Approximately 5 hours Notes on the Nickel-Metal Hydride batteries • If the poles of the Nickel-Metal Hydride batteries are dirty, the batteries may not charge properly. Occasionally clean the poles of the batteries and the terminals of the charger by wiping them with a dry cloth. • When transporting the Nickel-Metal Hydride batteries, be sure to use the battery case (supplied). If the +/- metal terminals are shorted, there is a possibility of danger from excessive heat or fire. • At the time of purchase, or when the Nickel- Metal Hydride batteries have not been used for a long time, they may not fully charge. This is typical of this type of battery, and is not a malfunction. If this happens, repeatedly using up the battery fully, and then recharging it, should correct the problem. • Even when Nickel-Metal Hydride batteries are not being used they loose their charge naturally over time. It is recommended that you recharge the batteries just before using them. • If you recharge Nickel-Metal Hydride batteries before fully using up the existing charge, the so-called memory effect* can occur, and the low battery warning will be triggered sooner than expected. Charging the battery after fully depleting the existing charge should correct the problem. * The “memory effect” – the situation in which a battery temporarily accepts a less than full charge. • To use up the batteries completely, put the camera in the slide show mode (page 63) and leave it that way until the batteries are used up. • Do not peel off the external seals or damage the batteries. Never use batteries from which the seals have been partially or completely removed, or batteries that have been split in any way. These may cause leakage, explosion, or heat-up of the battery, and personal scald or injury may be caused. These may cause a malfunction of the battery charger. Getting started Inserting the batteries , Open the battery cover. Slide it in the direction of the arrow with the OPEN button pressed, and it opens out. 1 122 3 12 , Insert the batteries. Match the +/. poles of the batteries to the +/ . marks inside the battery case. • Occasionally clean the poles of the batteries and the terminals of the battery cover by wiping them with a dry cloth. If the poles of the batteries or the terminals become covered with a film of dirt or oil from the skin, the operating time of the camera can be greatly reduced. , Close the battery cover. Close the battery cover while holding the batteries in. The cover is closed when it clicks. To remove the batteries Stand the camera on end, open the battery cover upward, then remove the batteries. • Make sure you do not drop the batteries when opening or closing the battery cover. Battery remaining indicator (When using the Nickel-Metal Hydride batteries) As the battery power decreases with use, the battery remaining indicator...
Эта инструкция также подходит к моделям:Фотоаппараты - DSC-P32 (2.54 mb)
Фотоаппараты - DSC-P72 (2.54 mb)