Оценок - , средний балл:
(
)
)
Производитель: Sunbeam
Размер: 448.68 kb
Название файла: 653de56a-0749-448c-8cba-9f0909566745.pdf
Язык инструкции:
Документ загружается, подождите пожалуйста
 |
Документ загружается, подождите пожалуйста
Фрагмент инструкции
Inspect the cord frequently for damage. Stop use immediately if damage is visible or unit stops or operates intermittently. SAVE THESE INSTRUCTIONS 1 MOUNTING INSTRUCTIONS For use on sheetrock or wood walls only. The Sunbeam ® Wall Mount hair dryer is designed for installation on sheetrock or wood walls only. To mount onto wall, be sure there are no hidden electrical circuits or pipes in the mounting location. FOLLOW THESE INSTRUCTIONS 1. Remove wall bracket from the unit. MOUNTING INSTRUCTIONS BRACKET Screw Plug Anchor Bushing WALL MOUNT UNIT (Base) LOCKING PLATE (Optional) 1632-040 shown here 2. Use the bracket or locking plate (optional) as template to mark position of holes for drilling close to electrical outlet, away from tub or sink. 3. Drill three 3/16 inch holes. 4. Insert the three anchor bushings by tapping lightly with a hammer until the shoulder of the bushing rests against the wall. 5. Position wall bracket and tighten the two bottom screws first, then tighten the top screw. ( Anchor bushings and screws are provided for you). 6. Match the slots on the back of the mounting base on the bracket. 7. Press base onto the hooks and slide down to insure secure mounting. (If using locking plate, remove small screw from center of magnet and replace with longer screw included). 8. Plug the unit into the nearby electrical outlet (110 volt, 50 – 60 cycle AC only). DANGER – To reduce risk of electrocution, do not install where unit can fall into tub or sink. 2 FEATURES OF YOUR HAIR DRYER Magnetic Hand Locking System Hi, Low Control Switch 3- Ft. Power Cord Hair Dryer Removable Lint Screen Expandable Power Cord 1632-040 shown here* Wall Mount Cradle On Button Test and Reset Buttons Off Button Off Switch Night Light ALCI *1632-020 is without the night light OPERATING INSTRUCTIONS This dryer is equipped with an appliance leakage circuit interrupter (ALCI) for your safety. This device is designed to make the appliance inoperable under some abnormal conditions (such as accidental immersion in water). After the appliance is plugged in, you must check your protective device as follows: 1. Press the “Reset” button on the ALCI device. 2. Press the “Test” button. The “Reset” button will pop out. This verifies that the protective device is working properly. 3. Press the “Reset” button once more to reactivate the safety device and use your appliance. REPEAT THE ABOVE PROCEDURE BEFORE EACH USE TO CONFIRM THAT THE PROTECTIVE DEVICE IS OPERATING. If your protective device does not operate above, please contact your nearest authorized Sunbeam 3 TO USE 1. Remove hair dryer from cradle. 2. To start the dryer, press the ON button on the wall mount unit. 3. Slide the control switch to: LOW position for styling hair, HIGH position for fastest drying. 4. Stop the dryer by pushing the OFF button or by replacing the unit to the mounting base, which will automatically engage the OFF switch. For your protection, this unit contains a thermostat that prevents the dryer from overheating. Should the air intake and/or air outlet become blocked or obstructed, the hair dryer will automatically shut off. If this occurs, slide the switch to OFF, unplug and allow dryer to cool. If dryer continues to turn off automatically, discontinue use and contact your nearest authorized Sunbeam distributor. CAUTION – Use your Sunbeam hair dryer with care. Directing a high volume of heat continuously to one area can overheat hair and scalp. When using a “High” heat setting, hold the blower opening a few inches away from the hair, drying one section at a time. Work layers of hair in quick strokes. Keep the dryer in motion until drying and styling are complete. LOWER WATTAGE CONSUMPTION For lower wattage consumption, there is an optional 1200/1500 switch found behind the Removable lint screen. (Patent Pending) 1200/1500Wattage Switch (Close-up) Lint Screen 1. Remove lint screen. 2. Locate wattage switch and move to the desired wattage. 3. Replace lint screen. 4 CARING FOR YOUR HAIR DRYER STORAGE 1. Always store dryer inside the base. 2. Do not mount or store dryer in an area with excessive heat or moisture. 3. Do not wrap cord around dryer. Allow to hang loosely from dryer. 4. Do not hang dryer by cord or use cord as a handle. 5. Store in a cool, dry place and out of reach of children. 6. Store where dryer will not be accidentally damaged from bumping or falling. Do not put anything on top of dryer. MAINTENANCE, CARE & CLEANING 1. Always unplug dryer from outlet before cleaning. 2. Clean dryer by wiping with a soft, lightly moistened cloth. 3. NEVER IMMERSE HAIR DRYER IN WATER. 4. The motor never needs oil or grease. 5. Check the removable lint screen. It is important that you clean the removable lint screen when hair, lint or dust begin to build up on it. To remove the screen, rotate counter-clockwise and loosen. To clean, brush the outside of the screen with a toothbrush to loosen lint, etc. Then turn the screen over and rinse under a running faucet. Towel...