Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Before installation, please read this manual carefully and keep for future reference. Required Tools • Flathead screwdriver • Drill • 1/16” drill bit • 5/32” drill bit • Phillips screwdriver Included Hardware: • 2 – Plastic anchors• 4 – Screws • 1 – Double sided Tape • 1 – 12 Volt battery Battery Installation: Chime Unit: 1. Make sure the Chime power is switched to the “OFF” position. 2. Remove battery cover by pressing the tab in the direction of the arrow and lifting at the same time. 3. Install 2 “AA” batteries noting the battery orientation inside the battery compartment. 4. Replace battery cover. Push Button: 1. Remove battery cover by using a small flat screwdriver. 2. Insert flat screwdriver in at the bottom of the Push Button to release the tab. 3. While the flat screwdriver is inserted at the bottom of the Push Button, press downwards to separate the battery cover from the Push Button. 4. Remove plastic tab in between the 12V battery and contact tab to allow button to operate. Press Linking the Push Button to the Chime Unit: 1. Switch the Chime power to the “ON” position. The red LED will begin blinking slowly. 2. Within 10 seconds of turning on the power, press the push button. The LED on the chime will blink rapidly and turn off. The Chime and Push Button have been successfully linked. 3. To test, press the Push Button and the Chime Unit should chime. Note: If linking fails or you change the batteries or turn the Chime Unit off and back on, you will have to re-link the Push Button to the Chime Unit. Perform steps 1 and 2 in the “Linking the Push Button to the Chime Unit.” Low Battery Indicator: The Chime Unit has a low battery indicator feature. When the battery is at 25 percent capacity, the LED on the Chime Unit will begin to blink and will continue to blink each time the Push Button is depressed. Replace the batteries and the LED will stop blinking. (You will have to re-link the Push Button to the Chime Unit) Installing the Push Button: 1. Push Buttons are mounted at the same height as the door knob or handle, between 36” – 44” above the floor. Remove the old push button and use this location to install your new Push Button. 2. Before mounting the Push Button run a test. Place the Push Button as close as you can to where you would install it. Place the Chime as close as possible to its installation site. Press the Push Button and see if the Chime rings. If the Chime does not ring see – Troubleshooting. *Remember: Button should be no farther away than 150 ft from the chime; and test before installation. Press Installation using the provided screws: 1. Remove the old push button and use this location to install your new Push Button. 2. Remove the battery cover as described in the installation of the battery. 3. Use the battery cover as a template to mark the position of the screws. 4. Using a 1/16th inch drill bit, drill a pilot hole for each screw. 5. Using a Phillips head screwdriver, mount the back cover using the screws provided. (Note: The back cover has an arrow and the word “Up” embossed on the inside of the cover. Position the back cover with the arrow pointing upwards and the word “Up” is at the top) 6. Press the Push Button on to the back cover by inserting the top of the Push Button onto the top of the back cover first and then pressing on the bottom of the Push Button to snap the bottom of the Push Button into place. Installation using the provided Double Sided Tape: 1. Clean the surface where you would like to mount the Push Button and the back of the Push Button. Use a mixture of 50/50 water to isopropyl alcohol. 2. Remove the battery cover as described in the installation of the battery. 3. Remove the backing from one side of the double sided tape and press it onto the back of the back plate of the Push Button. 4. Remove the backing from the other side of the double sided tape and press the back plate to the cleaned mounting surface. (Note: The back cover has an arrow and the word “Up” embossed on the inside of the cover. Position the back cover with the arrow pointing upwards and the word “Up” is at the top) 5. Press the Push Button on to the back cover by inserting the top of the Push Button onto the top of the back cover first and then pressing on the bottom of the Push Button to snap the bottom of the Push Button into place. Installing the Chime Unit: Note: Avoid mounting the Chime Unit on metal surfaces, as this may result in reduced range of transmission. The Chime Unit should also be mounted no farther than 150 feet from the Push Button. 1. Select a mounting location that is within the 150ft. range. 2. Use the supplied Chime template to mark mounting holes. a. If mounting to sheetrock: i. Using a 5/32nd inch drill bit, drill holes at the marked locations. ii. Insert the two wall anchors supplied iii. Screw in the two screws supplied leaving a .” of the screw extended out from the mounting surface. (See diagram) iv. Place the Chime Unit’s keyholes over the screws and gently ...