Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
(The doors should travel to the fully closed position) 7 8 From Dimmer Module Top of 24VDC Input Cabinet Front of Cabinet Installation Instructions CM6DH SERIES Activator Activator Button Figure 10 5. Press the "Open Door" button on the Remote Control. NOTE: If a different travel distance is required see "Door Travel Adjustment below. ADJUSTMENTS Adjust Door Travel Distance To adjust door travel distance: 1. Press and hold the activator button on the front of the motor box for 13 seconds. The Status Light on the front of the motor box will begin to blink alternately red and green. When this starts to happen release the Activator Button. When put into "Learn Moden the system runs back and forth several times and measures its environment, such as open and closed locations etc. The system will then stop and remember these learned measurements. Activator Figure 11 System Controls and Indicators Learn Mode The CM6DH system has no limit switches. The system uses an encoder on the motor to collect data and send it to the micro processor’s memory. The software "learns" about its environment (speed, time duration, stop points, etc.) during the initial setup of the unit and retains that information until requested to "relearn" its environment. The unit is shipped pre-set from the factory and will then continually adjusts to it’s enviornment on each activation. If for some reason you want to place the system into “Learn Mode” (such as to stop at other than its normal stop points), Press and hold the red activator button on the front of the motor box for approxamatly 13 seconds and then release it when the Status Light flashes quickly red, green, red, green, red, green. Figure 12 The controller will then be in “Learn Mode” (The door will move for 3 seconds, stop for 10 seconds, and when it starts moving again it will be in it’s “Learn Mode”). When put into “Learn Mode” the mechanism runs back and forth several times and measures it’s environment, such as open and closed locations etc., and then stops and remembers these learned measurements, so that next time the system runs it knows where to start and stop. Status Light Codes There is a light on the front of the mechanism motor box that will tell through its pattern of flashes and colors what the mechanism is doing. Status Indicator Figure 13 Normal Doors At Rest -The Status Light will be on steady green. Normal Run Motion of Doors - The Status Light will flash in groups of 2 green followed by a pause. In normal run motion the doors on the system have a variable speed. The doors will start slowly, accelerate to a fast speed, and then slow down before coming to a stop. Doors Obstructed - The Status Light will flash in groups of 3 red followed by a pause. If the doors meet an obstruction they will sense the obstruction, stop momentarily, and move in the opposite direction for a few seconds. ---- Remove the obstruction and then activate the doors. They should return to normal run motion. Doors Obstructed Both Ways - The Status Light will flash in groups of 4 red followed by a pause. Similar to Doors Obstructed but doors are prevented from moving in either direction. ---- Remove the obstruction and then activate the doors. They should return to normal run motion. Travel Too Far - The Status Light will flash in groups of 5 red followed by a pause. The motor is running but the doors are not moving. ---- Has the motor box been uncoupled from the CM6DH SERIES Installation Instructions track, or is the motor box bent, causing it to become uncoupled Control Input on Front of Motor Box from the track? Power Loss - The Status Light will be on solid red. ---- There has been a power loss (due to an electrical storm, etc.). When next activated the doors will move at a slow speed to their full closed position. If the doors are already closed they will not move. The Status Light will return to solid green and the doors are ready for normal activation. Optional Control Input Connections Control Input- 8 position RJ 45 modular phone jack Discrete control for use with 3rd party control. • Position 8- Open • Position 7- Stop IR Receiver “Eye” input for Eubank, Inc. supplied external IR reciever only. • Position 6 - V out • Position 5 - Vcc, 5v Radio Power for external RF receiver only. • Position 4 - 24 VDC Sequence control for use with 3rd party control. • Position 3 - Sequence- Open, Stop, Close, Stop • Position 2 - Common Discrete control for use with 3rd party control. • Position 1 - Close Control Input Figure 14 NOTE:Making a momentary dry contact closure between the common and the open, closed, stop, or sequence will activate the system in that mode. Control Input on Front of Motor Box Figure 15 Installation Instructions CM6DH SERIES CM6DH SERIES Installation Instructions USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378 P 800.582.6480 / 952.894.6280 F 877.894.6918 / 952.894.6918 Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands P +31 (0)40 2668620 F +31 (0)40 ...