Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
• Do not place the drive in direct sunlight. • Avoid low- or high-temperature environments. • Avoid high-humidity environments. Handle with caution to prevent damage from external shock. Do not drop the drive, and protect it fromsevere shocks. • It can damage the drive or cause it to malfunction. Do not move the drive while in operation and do not attempt to open the disc tray byforce. Make sure to close all working programs before attempting to open the tray and always use the open/close button. Do not use cracked, distorted or damaged discs. Do not insert a pin into the emergency opening while in operation. In particular, a disc with a crack on the inner tracks may break while in use. • Never allow food particles or foreign substances to enter the drive casing. • To protect against the risk of fire, do ot spill such liquids as alcohol and benzene on the drive. Do not disassemble, attempt to repair or modify the device without express approval as directed in the manual. • To reduce the risk of damage, electric shock, and fire. Important to read and understand at all times Do not disassemble 1. Check to see that the disc does not have a crack before use. If the disc has a crack (especially around the center hole), it is recommended that you make a copy immediately and use the copy instead. When a cracked disc is used continuously,the size of the crack is likely to grow and it will eventually result in irreparable damage to the disc. 2. Do not use low quality discs (i.e., illegal products, scratched or damaged discs). • Any change or modification not expressly approved by designated qualified personnel could void your authority to operate this device. Warning/Caution Warning: To warn the user that failure to comply with the instructions may result in serious injury or death. Caution: To caution the user that failure to comply with the instructions may result in damage to property. 5 • Failure to do so may cause the device to fall onto a hard surface, resulting in damage or malfunction. When using one EIDE cable • Connect the cable to the SL (Slave) of the Master/Slave Select Terminal at the rear of the DVD Writer. When using two EIDE cable • Connect the cable to the MA (Master) of the Master/Slave Select Terminal at the rear of the DVD Writer. - If there is only one Optical drive: select MA (Master). Hard Drive Slave Drive (Choose the SL Jumper) MainBoard Hard Drive Master Drive (Choose the MA Jumper) MainBoard SEC 1 PRI 1 SEC 1 PRI 1 -If there is two Optical drive, select MA (Master) / SL (Slave). Hard Drive Master Drive (Choose the MA Jumper) Slave Drive (Choose the SL Jumper) MainBoard (Choose the MA Jumper) (Choose the SL Jumper) Disc compartment Emergency eject hole LED Disc compartment Eject Button If the compartment does not open when you press the Eject button, power off the computer, insert a pin or unfolded paper clip in the hole and push firmlhy) Front Rear Sound output terminal Interface terminal Digital output terminal Master/slave select terminal Power terminal Accessories User Guide, Screw 4ea Introduction • Design and specifications are subject to change without prior notice. Connecting the Cables to the DVD Writer Connecting the Cables Connecting the power cable • The 4-pin power cable from the internal power unit of your computer must be connected to the power terminal the rear of the DVD Writer. 1 Connecting the EIDE cable from a sound card • Connect the 4-pin audio cable between the sound output terminal on the DVD Writer and the audio input terminal on the sound card. 4 Installing a jumper on the master/slave select terminal • Connect a jumper to the rear side of the DVD Writer. If the jumper is connected to MA (Master), it will work in the Master mode. If the jumper is connected to SL (Slave), it will work in the Slave mode. If the jumper is connected to CS (CSEL), you can control the device by using the host interface signal CSEL. (In general, connection to MA is recommended.) 2 Connecting the EIDE cable • Insert the EIDE cable, which is connected to the hard disk to the interface terminal. (Place the red line of the cable close to the Pin 1.) 3 Power cable EIDE cable Master/slave select terminal Audio cable CS : Cable Select(CSEL) SL : Slave MA: Master 6 7 Installing the Drive Installing the DVD Writer If necessary, attach a horizontal bracket to both sides of the drive. • You can purchase these accessories separately from your computer dealer. (Screws for use: M3 X 6 X 4) 1 Remove the plate from a free expansion slot and install the DVD Writer, as shown in the illustration. • If you have no free expansion slot, install the drive in place of the diskette drive. • Make sure to use the standardized screws supplied (M3X6). - To use screws other than M3X6 may result in malfunction. Intel Pentium 800MHz(or higher), 256 MB of RAM (or higher)with an EIDE interface,Windows 2000/ XP/ Vista 2 How to install the DVD Writer on your PC. First, remove the cover; connect the cable to the DVD Writer ...
Эта инструкция также подходит к моделям:DVD-проигрыватели - SH-S202N (850.82 kb)